en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro
en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro
en/ACS800-04/U4 Hardware Manuals - VAE ProSys sro
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
111CE markingA CE mark is attached to the drive to verify that the unit follows the provisions of the European LowVoltage and EMC Directives (Directive 73/23/EEC, as am<strong>en</strong>ded by 93/68/EEC and Directive 89/336/EEC, as am<strong>en</strong>ded by 20<strong>04</strong>/108EC).DefinitionsEMC stands for Electromagnetic Compatibility. It is the ability of electrical/electronic equipm<strong>en</strong>t tooperate without problems within an electromagnetic <strong>en</strong>vironm<strong>en</strong>t. Likewise, the equipm<strong>en</strong>t must notdisturb or interfere with any other product or system within its locality.First <strong>en</strong>vironm<strong>en</strong>t includes establishm<strong>en</strong>ts connected to a low-voltage network which supplies buildingsused for domestic purposes.Second <strong>en</strong>vironm<strong>en</strong>t includes establishm<strong>en</strong>ts connected to a network not supplying domestic premises.Drive of category C2: drive of rated voltage less than 1000 V and int<strong>en</strong>ded to be installed andcommissioned only by a professional wh<strong>en</strong> used in the first <strong>en</strong>vironm<strong>en</strong>t. Note: A professional isa person or organisation having necessary skills in installing and/or commissioning power drivesystems, including their EMC aspects.Drive of category C3: drive of rated voltage less than 1000 V and int<strong>en</strong>ded for use in the second<strong>en</strong>vironm<strong>en</strong>t and not int<strong>en</strong>ded for use in the first <strong>en</strong>vironm<strong>en</strong>t.Drive of category C4: drive of rated voltage equal to or above 1000 V, or rated curr<strong>en</strong>t equal to or above400 A, or int<strong>en</strong>ded for use in complex systems in the second <strong>en</strong>vironm<strong>en</strong>t.Compliance with the EMC DirectiveThe EMC Directive defines the requirem<strong>en</strong>ts for immunity and emissions of electrical equipm<strong>en</strong>t usedwithin the European Union. The EMC product standard [EN 61800-3 (20<strong>04</strong>)] covers requirem<strong>en</strong>tsstated for drives.Compliance with the EN 61800-3 (20<strong>04</strong>)First <strong>en</strong>vironm<strong>en</strong>t (drive of category C2)The drive complies with the standard with the following provisions:1. The drive is equipped with EMC filter +E202.2. The motor and control cables are selected as specified in the <strong>Hardware</strong> Manual.3. The drive is installed according to the instructions giv<strong>en</strong> in the <strong>Hardware</strong> Manual.4. Maximum cable l<strong>en</strong>gth is 100 metres.WARNING! The drive may cause radio interfer<strong>en</strong>ce if used in a resid<strong>en</strong>tial or domestic <strong>en</strong>vironm<strong>en</strong>t.The user is required to take measures to prev<strong>en</strong>t interfer<strong>en</strong>ce, in addition to the requirem<strong>en</strong>ts for CEcompliance listed above, if necessary.Note: It is not allowed to install a drive equipped with EMC filter +E202 on IT (unearthed) systems. Thesupply network becomes connected to earth pot<strong>en</strong>tial through the EMC filter capacitors which maycause danger or damage the unit.Technical data