G4 Multi Channel Weighing Instrument. PM/DT/HE Technical Manual

More documents

Recommendations

Info

Technical ManualAOUT3-4 Value (Integer format)ByteOffset + 0Offset + 1Offset + 2Offset + 3Offset + 4Offset + 5Offset + 6Offset + 7Offset + 8Offset + 9Offset + 10Offset + 11Offset + 12Offset + 13Offset + 14Offset + 15ContentAnalog output value 3, int MSBAnalog output value 3, intAnalog output value 3, intAnalog output value 3, intAnalog output value 3, dec MSBAnalog output value 3, decNot usedNot usedAnalog output value 4, int MSBAnalog output value 4, intAnalog output value 4, intAnalog output value 4, intAnalog output value 4, dec MSBAnalog output value 4, decNot usedNot used6-40
G4 Multi Channel Weighing InstrumentExamplesExample 1: Setting ‘Level 1 Value’ to 123.5 (Writing to float value register).1. Make sure that the previous command was not 251.Set command byte (00) to 0 if previous command was 251.2. Set number of registers (2) to write in byte 01.3. Set start address (46026) in bytes 02 and 03.See section ‘6 Communication – Modbus protocol – General registers’.4. Set the following four bytes (04 – 07) to the value to write (123.5).5. Enter the command (251) in byte 00.Byte Description Dec Hex00 Command 251 FB01 Number of registers to write 2 0202 – 03 Start address 46026 B3 CA04 – 07 Value to write in register 1 and 2 123.5 42 F7 00 0008 – 15 Write registers 3 – 6. ⎯ ⎯Example 2: Setting ‘Setpoint 14 value’ to 123.5 (Writing to integer value register).1. Make sure that the previous command was not 251.Set command byte (00) to 0 if previous command was 251.2. Set number of registers (3) to write in byte 01.3. Set start address (42169) in bytes 02 and 03.See section ‘6 Communication – Modbus protocol – General registers’.4. Set the following four bytes (04 – 07) to the value to write 123.50,i.e. 12350 and two decimals.5. Set bytes 08 and 09 to number of decimals. In this example is 2 decimals used.6. Enter the command (251) in byte 00.Byte Description Dec Hex00 Command 251 FB01 Number of registers to write 3 0302 – 03 Start address 42169 A4 B904 – 07 Value to write in register 1 and 2 12350 00 00 30 3E08 – 09 Value to write to register 3 2 00 0210 – 15 Write registers 4 – 6. ⎯ ⎯6-41
Page 1:
GBG4 Multi ChannelWeighing Instrume
Page 4 and 5:
Technical ManualPRECAUTIONSREAD thi
Page 6 and 7:
Technical ManualFunctionsMeasuremen
Page 8 and 9:
Technical ManualTechnical dataEnclo
Page 10 and 11:
Technical ManualCPUModule typeCPU m
Page 12 and 13:
Technical ManualHS WF2Module typeMa
Page 14 and 15:
Technical ManualDeviceNetModule typ
Page 16 and 17:
Technical ManualOrdering informatio
Page 18 and 19:
Technical Manual1-14
Page 20 and 21:
Technical Manual!Electrical install
Page 22 and 23:
Technical ManualField BusSlot for o
Page 24 and 25:
Technical ManualAC SUPPLY - 110-240
Page 26 and 27:
Technical Manual4-wire connectionTr
Page 28 and 29:
Technical ManualAOUT1 and AOUT4!The
Page 30 and 31:
Technical ManualProfibus-DP Fieldbu
Page 32 and 33:
Technical ManualDeviceNet Fieldbus
Page 34 and 35:
Technical ManualFront panelDisplayA
Page 36 and 37:
Technical Manual2-18
Page 38 and 39:
Technical Manualrate and data forma
Page 40 and 41:
Technical ManualWhen editing a choi
Page 42 and 43:
Technical ManualMenu structureMain
Page 44 and 45:
Technical ManualParametersOn the fo
Page 46 and 47:
Technical ManualRange/AlternativesD
Page 48 and 49:
Technical ManualRange/Alternatives
Page 50 and 51:
Technical ManualRange/AlternativesE
Page 52 and 53:
Technical ManualRange/Alternatives1
Page 54 and 55:
Technical ManualRange/Alternatives1
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Technical ManualRange/AlternativesM
Page 64 and 65:
Page 66 and 67:
Technical ManualRange/AlternativesD
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Technical ManualIf the weight indic
Page 78 and 79:
Technical ManualData sheet calibrat
Page 80 and 81:
Technical Manualfor the selected nu
Page 82 and 83:
Technical ManualDisplay alternative
Page 84 and 85:
Technical ManualSecurity locksIn th
Page 86 and 87:
Technical ManualGross/Net operation
Page 88 and 89: Technical ManualMain menuTo reach t
Page 90 and 91: Technical ManualLevel supervisionTh
Page 92 and 93: Technical ManualUse of inputs and o
Page 94 and 95: Technical ManualFlow rateGeneralThe
Page 96 and 97: Technical ManualFlow rate update ti
Page 98 and 99: Technical Manual5-18
Page 100 and 101: Technical ManualSetup of Modbus RTU
Page 102 and 103: Technical ManualGeneral registersTh
Page 104 and 105: Technical ManualData type:IntegerDa
Page 107 and 108: G4 Multi Channel Weighing Instrumen
Page 137: G4 Multi Channel Weighing Instrumen
Page 152: Publication 600 852 R2© Vishay Nob
show all

G4 Multi Channel Weighing Instrument. PM/DT/HE Technical Manual

Create successful ePaper yourself

Delete template?

Save as template?