G4 Multi Channel Weighing Instrument. PM/DT/HE Technical Manual

More documents

Recommendations

Info

Technical ManualRange/AlternativesExplanation andresult of alternatives.Output 11 Setpoint (- Output 18 Setpoint)123….141516< 1 >1: Setpoint number 1 uses the output.2: Setpoint number 2 uses the output.3: Setpoint number 3 uses the output.….14: Setpoint number 14 uses the output.15: Setpoint number 15 uses the output.16: Setpoint number 16 uses the output.Note: this parameter is only shown ifparameter ‘Output 11 Source’ is ‘Setpoint’.3-36
G4 Multi Channel Weighing InstrumentRange/AlternativesExplanation andresult of alternatives.Menu ‘Analog Outputs’NOTE: There are 4 possible analog outputs each with the 8 parameters describedbelow. If the selected analog output module is AOUT4 there will be parameters for fouranalog outputs displayed, if the AOUT1 is selected only the parameters for the firstanalog output (shown below) will be shown. If no AOUT module at all is selected themenu ‘Analog Outputs’ will not be shown.AOUT 1 Source (- AOUT 4 Source)Not in useGross WeightNet WeightDisp. WeightFlow Rate< Not in use >AOUT 1 Scale (- AOUT 4 Scale)12345678< 1 >Defines the value to represent on analog output 1.Not in use: The analog output is not used.Gross Weight: The output represents gross weight.Net Weight: The output represents net weight.Disp. Weight: The output represents gross or netweight, even if flow rate is displayed.Flow Rate: The output represents flow rate.1: Scale number 1 uses this analog output.2: Scale number 2 uses this analog output.….8: Scale number 8 uses this analog output.Note: this parameter is not shown if parameter‘AOUT 1 Source’ is ‘Not in use’.AOUT 1 Output Type (- AOUT 4 Output Type)+/– 20 mA–12 – 20 mA0-20 mA4-20 mA+/–10 V0-10 VDefines the type of signal, used to representthe weight/flow rate value at this Analog output.+/–20mA, –12 - 20mA: bipolar current output.0-20mA, 4-20mA: monopolar current output.+/–10V: bipolar voltage output.0-10V: monopolar voltage output.Note: this parameter is not shown if parameter‘AOUT 1 Source’ is ‘Not in use’.Note that in most cases some over range is available.+/-20 mA and -12 – 20 mA ranges are limitedat -22 and +22 mA.4 -20 mA range is limited at +4 and +22 mA.0 -20 mA is limited at 0 and +22 mA.+/-10 V is limited at -11 and +11V.0–10 V is limited at 0 and +11V.3-37
Page 1:
GBG4 Multi ChannelWeighing Instrume
Page 4 and 5:
Technical ManualPRECAUTIONSREAD thi
Page 6 and 7:
Technical ManualFunctionsMeasuremen
Page 8 and 9:
Technical ManualTechnical dataEnclo
Page 10 and 11:
Technical ManualCPUModule typeCPU m
Page 12 and 13:
Technical ManualHS WF2Module typeMa
Page 14 and 15:
Technical ManualDeviceNetModule typ
Page 16 and 17:
Technical ManualOrdering informatio
Page 18 and 19:
Technical Manual1-14
Page 20 and 21:
Technical Manual!Electrical install
Page 22 and 23: Technical ManualField BusSlot for o
Page 24 and 25: Technical ManualAC SUPPLY - 110-240
Page 26 and 27: Technical Manual4-wire connectionTr
Page 28 and 29: Technical ManualAOUT1 and AOUT4!The
Page 30 and 31: Technical ManualProfibus-DP Fieldbu
Page 32 and 33: Technical ManualDeviceNet Fieldbus
Page 34 and 35: Technical ManualFront panelDisplayA
Page 36 and 37: Technical Manual2-18
Page 38 and 39: Technical Manualrate and data forma
Page 40 and 41: Technical ManualWhen editing a choi
Page 42 and 43: Technical ManualMenu structureMain
Page 44 and 45: Technical ManualParametersOn the fo
Page 46 and 47: Technical ManualRange/AlternativesD
Page 48 and 49: Technical ManualRange/Alternatives
Page 50 and 51: Technical ManualRange/AlternativesE
Page 52 and 53: Technical ManualRange/Alternatives1
Page 54 and 55: Technical ManualRange/Alternatives1
Page 62 and 63: Technical ManualRange/AlternativesM
Page 66 and 67: Technical ManualRange/AlternativesD
Page 76 and 77: Technical ManualIf the weight indic
Page 78 and 79: Technical ManualData sheet calibrat
Page 80 and 81: Technical Manualfor the selected nu
Page 82 and 83: Technical ManualDisplay alternative
Page 84 and 85: Technical ManualSecurity locksIn th
Page 86 and 87: Technical ManualGross/Net operation
Page 88 and 89: Technical ManualMain menuTo reach t
Page 90 and 91: Technical ManualLevel supervisionTh
Page 92 and 93: Technical ManualUse of inputs and o
Page 94 and 95: Technical ManualFlow rateGeneralThe
Page 96 and 97: Technical ManualFlow rate update ti
Page 98 and 99: Technical Manual5-18
Page 100 and 101: Technical ManualSetup of Modbus RTU
Page 102 and 103: Technical ManualGeneral registersTh
Page 104 and 105: Technical ManualData type:IntegerDa
Page 107 and 108: G4 Multi Channel Weighing Instrumen
Page 123 and 124:
G4 Multi Channel Weighing Instrumen
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 152:
Publication 600 852 R2© Vishay Nob
show all

G4 Multi Channel Weighing Instrument. PM/DT/HE Technical Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?