emerson-300510en-users-manual

Recommendations

Info

Rosemount Raptor System Configuration Manual 300510EN, Rev AA December 2010 Advanced Configuration The Advanced Tank Setup window allows you to change mapping of tank measurement variables to gauge output. This option can for example be used to map relay status presentation in the TankMaster WinOpi program to the relay outputs of a Rosemount 2410 Tank Hub. NOTE! Advanced configuration should only be used when there is no appropriate option available in the standard Tank Configuration window. To change tank parameter mapping do the following: a. Click the Advanced button in the Tank Configuration window. b. For each tank input variable you can change gauge output only, or you can change to another gauge as well. Simply put the mouse pointer in the Gauge or Output field of the desired Tank Input variable (Level, Level rate, etc.) and choose the appropriate option from the drop-down list. c. Click the OK button to close the Advanced Tank Setup window. 9. In the Tank Configuration window, click the Next button to proceed to the next step of the tank installation procedure. 5-108 Section 5. Installing a Raptor Level Gauging System
System Configuration Manual 300510EN, Rev AA December 2010 Rosemount Raptor 10. Specify parameter value range to be used in various windows for presentation of measurement data. Also choose whether to use measurement values (Automatic) from the available instruments or <strong>manual</strong> values. The Free Water Level, Liquid Pressure, and Vapor Pressure parameters are set to Value Source=Manual by default. Therefore, the tank needs to be configured for automatic measurements when these type of instruments are used. The Value Entry window allows you to disable automatic measurements for selected parameters in case you need to remove an instrument for service purposes. To use <strong>manual</strong> values do the following: 1. Chose a measurement variable in the left-hand list of the Value Entry window. 2. Set Value Source to Manual. 3. Type the desired value in the Value entry field. Now the automatic measurement is disabled for the selected tank measurement variable. Manual values are marked yellow in order to distinguish from automatically measured values. Section 5. Installing a Raptor Level Gauging System 5-109
Page 1:
System Configuration Manual 300510E
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94: System Configuration Manual 300510E
Page 143: System Configuration Manual 300510E
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 246:
show all

emerson-300510en-users-manual

Create successful ePaper yourself

Delete template?

Save as template?