emerson-300510en-users-manual

Recommendations

Info

Rosemount Raptor System Configuration Manual 300510EN, Rev AA December 2010 To configure the FCU Slave Database: a. Select a free database position (1A, 2A ...) for the level gauge device to be configured. b. Choose Slave type=2410 Level. The corresponding Slave Database position (1B, 2B ...) for temperature transmitters and other auxiliary tank devices is automatically assigned to Slave Type=2410 Temp. c. Enter Modbus addresses for level gauges and auxiliary tank devices (ATD). Ensure that the same database positions, .i.e. 1A/1B, 2A/2B and so on, are used for level gauges and ATDs on the same tank. d. Select the communication fieldbus (FB1, FB2, FB3, FB4) that the Rosemount 2410 is connected to. Normally there are four fieldbus ports available on the 2160 Field Communication Unit. The RS485 bus is the standard fieldbus interface for a Rosemount 2410 Tank Hub connected to a Rosemount 2160 FCU. e. If temperature elements are installed in the tank, type the number of elements in the Temp column. The 2160 Slave Database and the 2410 Tank Database In a typical Raptor system a Rosemount 2160 FCU collects measurement data from a number of tanks via one or more Rosemount 2410 Tank Hubs. The Modbus addresses of the field devices on the tank need to be stored in the 2160 FCU slave database as well as in the Rosemount 2410 tank database for proper communication with the control room PC. Level Gauge Modbus Address - 2410 Level The 2410 Level address field in the 2160 FCU slave database is used for level gauges such as the Rosemont 5900S. This address also needs to be stored in the 2410 tank database as the Level Modbus address. This is normally done as part of the installation procedure of the Rosemount 2410 as described in chapter “Installing a Rosemount 2410 Tank Hub” on page 5-38. ATD Device Modbus Address - 2410 Temp The 2410 Temp Modbus address in the 2160 FCU slave database is used for all devices on a tank except level gauges. This address also needs to be stored in the ATD Modbus address field of the 2410 tank database. This is normally done as part of the installation procedure of the Rosemount 2410 as described in chapter “Installing a Rosemount 2410 Tank Hub” on page 5-38. The first tank in the 2410 tank database uses the Modbus address of the 2410 Tank Hub itself as the ATD Modbus address. Tank number two, three etc. use separate ATD Modbus addresses. The 2410 Modbus address is automatically set as the ATD Modbus address for tank position 1 in the 2410 Tank Database as illustrated in Figure 5-5 on page 5-34. It is recommended that address range 1 to 99 is used for level gauges and 101 to 199 for ATD devices. See “Examples of 2160 FCU Slave Database Configuration” on page 5-32 for further information on how to configure the Slave Database of the 2160 Field Communication Unit (FCU) and the Tank Database of the Rosemount 2410 Tank Hub. 5-30 Section 5. Installing a Raptor Level Gauging System
System Configuration Manual 300510EN, Rev AA December 2010 Rosemount Raptor Summary of FCU Slave Database entry fields Slave type Address FCU field bus Temps Ain/Cin Hin Relays Interval 1 Interval 2 Level Offset 2410 Level, (pos 1A-32A) or 2410 Temp, (pos 1B-32B) The Modbus address used for the connected devices. For level gauges it is recommended that address 1 to 99 is used. For ATD devices address 101 to 199 are recommended. The field bus that the selected device is connected to. In the standard configuration there are four field buses available. The number of temperature elements connected to the temperature transmitter (for example a Rosemount 2240S). Automatically configured Automatically configured Automatically configured Automatically configured Automatically configured Not used Section 5. Installing a Raptor Level Gauging System 5-31
Page 1:
System Configuration Manual 300510E
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16: System Configuration Manual 300510E
Page 65: System Configuration Manual 300510E
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 246:
show all

emerson-300510en-users-manual

Create successful ePaper yourself

Delete template?

Save as template?