emerson-300510en-users-manual

Recommendations

Info

Rosemount Raptor System Configuration Manual 300510EN, Rev AA December 2010 5.7.3 Advanced Configuration In addition to the basic configuration, there are advanced configuration options available for the Rosemount 5900S Radar Level Gauge. These may be used to optimize measurement performance for certain applications. Tank Shape The Tank Type and Tank Bottom Type parameters optimize the Rosemount 5900S for various tank geometries and for measurements close to the tank bottom. To configure the 5900S Radar Level Gauge for a certain tank shape, do the following: 1. In the 5900S RLG Properties window select the Tank Shape tab: 2. Select a Tank Type option that matches the actual tank. Choose Unknown if there is no option that is applicable. 3. Select Tank Bottom Type that matches the actual tank. Choose Unknown if there is no option that is applicable. 4. Click the OK button to save the configuration and close the window. 5-62 Section 5. Installing a Raptor Level Gauging System
System Configuration Manual 300510EN, Rev AA December 2010 Rosemount Raptor Tank Environment Certain tank conditions may require additional configuration of the 5900S Radar Level Gauge in order to optimize measurement performance. By considering environmental conditions in the tank, the 5900S can compensate for conditions such as rapid level change, weak echo signals, or varying surface echo amplitudes. To configure the 5900S Radar Level Gauge for special tank conditions: 1. In the 5900S RLG Properties window select the Environment tab: 2. Select the check boxes that correspond to the conditions in the tank. Use as few options as possible. It is recommended that no more than two options are used simultaneously. 3. Choose the Product Dielectric Range from the drop-down list. Choose the Unknown option if the correct value range is unknown or if the contents of the tank is changing on a regular basis. 4. Click the OK button to save the configuration and close the window. See the Rosemount 5900S Reference Manual (Document No. 300520EN) for more information on tank environment settings. Section 5. Installing a Raptor Level Gauging System 5-63
Page 1:
System Configuration Manual 300510E
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48: System Configuration Manual 300510E
Page 97: System Configuration Manual 300510E
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 246:
show all

emerson-300510en-users-manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?