4 - Fagor Automation

More documents

Recommendations

Info

4. CANNED CYCLES OF THE EDITOR Reaming CNC 8065 (REF: 1209) ·114· 4.8.1 Basic operation. Canned cycles (·M· model) 1 It starts the spindle in the requested direction. 2 Rapid movement (G0), up to the XY point and the safety plane (Zs). Depending on the starting plane, it first moves in XY and then in Z or vice versa. 3 Rapid movement (G0) up to the approach plane. 4 Penetration at feedrate "F". 5 Dwell "t". 6 Withdrawal, at feedrate "F", to the approach plane. 7 Rapid movement (G0) up to the safety plane (Zs). If it has a multiple machining operation associated with it, it executes the following steps as often as necessary: 8 Rapid movement (G0) to the next point. 9 Repeats steps 3, 4, 5, 6, 7.
Canned cycles (·M· model) 4.9 Boring. Geometric parameters: X, Y Machining point. Z Part surface coordinate. Zs Safety plane coordinate. Dp Part surface approach distance. The editor will only show this data if the user has configured the editor to allow it. If this option is not enabled, the cycle assumes an approach distance of 1 mm. P Total depth. Machining parameters: F Feedrate. S Spindle speed. T Tool. D Tool offset. t Dwell at the bottom, in seconds. Withdrawal direction (icon). Spindle turning direction (icon). Programming of M functions. Next tool. At feedrate "F" and the spindle turning. In rapid (G0) with the spindle stopped. Clockwise. Counterclockwise. Activating or deactivating the execution of M functions before machining. The cycle allows editing up to 4 M functions. To execute only some of them, define them first and leave the rest of the data unprogrammed. The editor will only show this option if the user has configured the editor to allow programming M functions. Activating or deactivating the preparation of the next tool. The editor will only show this option if the user has configured the editor to allow programming the next tool. 4. CANNED CYCLES OF THE EDITOR Boring. CNC 8065 (REF: 1209) ·115·
Page 1 and 2:
CNC 8065 Canned cycles (·M· model
Page 3 and 4:
Canned cycles (·M· model) INDEX A
Page 5 and 6:
Canned cycles (·M· model) ABOUT T
Page 7:
Canned cycles (·M· model) Softwar
Page 11:
Canned cycles (·M· model) VERSION
Page 14 and 15:
CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18:
Canned cycles (·M· model) WARRANT
Page 19:
Canned cycles (·M· model) MATERIA
Page 23 and 24:
MILLING CANNED CYCLES. 1.1 General
Page 25 and 26:
Canned cycles (·M· model) 1.1.1 D
Page 27 and 28:
Canned cycles (·M· model) 1.1.3 P
Page 29 and 30:
Canned cycles (·M· model) Example
Page 31 and 32:
Canned cycles (·M· model) T1 M6 G
Page 33 and 34:
Page 35 and 36:
Canned cycles (·M· model) K Dwell
Page 37 and 38:
Page 39 and 40:
Canned cycles (·M· model) 4 Dwell
Page 41 and 42:
Canned cycles (·M· model) 1.5 G84
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Canned cycles (·M· model) E Dista
Page 49 and 50:
Page 51 and 52:
Canned cycles (·M· model) 3 Rapid
Page 53 and 54:
Page 55 and 56:
Canned cycles (·M· model) 4 Penet
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64: Canned cycles (·M· model) L Finis
Page 65 and 66: MULTIPLE MACHINING 2 The programmer
Page 67 and 68: Canned cycles (·M· model) Basic o
Page 69 and 70: Canned cycles (·M· model) 2.2 G16
Page 71 and 72: Canned cycles (·M· model) 2.2.1 P
Page 73 and 74: Canned cycles (·M· model) Y J Y D
Page 77 and 78: Canned cycles (·M· model) 2.4.1 P
Page 79 and 80: Canned cycles (·M· model) Basic o
Page 83 and 84: CYCLE EDITOR 3 The cycle editor is
Page 85 and 86: Canned cycles (·M· model) 3.1 Con
Page 87 and 88: Canned cycles (·M· model) 3.3 Sel
Page 89 and 90: Canned cycles (·M· model) If the
Page 91 and 92: CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94: Canned cycles (·M· model) 4.1.2 W
Page 95 and 96: Canned cycles (·M· model) 4.1.3 V
Page 97 and 98: Canned cycles (·M· model) 4.2 Cen
Page 99 and 100: Canned cycles (·M· model) 4.2.1 B
Page 105 and 106: Canned cycles (·M· model) Spindle
Page 107 and 108: Canned cycles (·M· model) 4.6 Tap
Page 111 and 112: Canned cycles (·M· model) Machini
Page 113: Canned cycles (·M· model) 4.8 Rea
Page 117 and 118: Canned cycles (·M· model) 4.10 Bo
Page 119 and 120: Canned cycles (·M· model) 4.10.1
Page 121 and 122: Canned cycles (·M· model) I Penet
Page 125 and 126: Canned cycles (·M· model) Type of
Page 127 and 128: Canned cycles (·M· model) θ Pene
Page 129 and 130: Canned cycles (·M· model) 4.13 Ci
Page 131 and 132: Canned cycles (·M· model) The fin
Page 135 and 136: Canned cycles (·M· model) F Surfa
Page 139 and 140: Canned cycles (·M· model) 4.15 2D
Page 141 and 142: Canned cycles (·M· model) T Rough
Page 147 and 148: Canned cycles (·M· model) New pro
Page 149 and 150: Canned cycles (·M· model) P.XY Na
Page 151 and 152: Canned cycles (·M· model) Fz Pene
Page 153 and 154: Canned cycles (·M· model) Program
Page 157 and 158: Canned cycles (·M· model) Configu
Page 159 and 160: Canned cycles (·M· model) 4.17 Re
Page 161 and 162: Canned cycles (·M· model) Program
Page 165 and 166:
Canned cycles (·M· model) I Penet
Page 167 and 168:
Canned cycles (·M· model) 4.18.1
Page 169 and 170:
Canned cycles (·M· model) Z Part
Page 171 and 172:
Page 173 and 174:
Canned cycles (·M· model) The rou
Page 175 and 176:
Page 177 and 178:
Canned cycles (·M· model) F Surfa
Page 179 and 180:
Page 181 and 182:
Canned cycles (·M· model) The rou
Page 183 and 184:
Canned cycles (·M· model) Program
Page 185 and 186:
Page 187 and 188:
Canned cycles (·M· model) 4.24 Mu
Page 189 and 190:
Canned cycles (·M· model) 4.25 Mu
Page 191 and 192:
Canned cycles (·M· model) 4.27 Ra
Page 193 and 194:
Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?