4 - Fagor Automation

More documents

Recommendations

Info

4. CANNED CYCLES OF THE EDITOR Circular boss. CNC 8065 (REF: 1209) ·164· 4.18 Circular boss. Geometric parameters: Xc, Yc Center of the boss. R Boss radius. Z Part surface coordinate. Zs Safety plane coordinate. P Total depth. Q Amount of stock to be removed. Roughing parameters: Canned cycles (·M· model) The roughing operation machines the boss leaving the following finishing stocks. Both stocks are defined as finishing parameters. δ Finishing stock on the side walls. δz Finishing stock at the base of the boss. The roughing operation defining parameters are: Δ Maximum milling pass or width. The cycle recalculates the pass so that all the passes are identical, with the same value as or smaller than the one programmed. If programmed with a 0 value, it assumes a value of 3/4 of the diameter of the selected tool.
Canned cycles (·M· model) I Penetration step. If programmed with a positive sign (I+), the cycle recalculates the step so all the penetrations are identical with the same value as or smaller than the one programmed. If programmed with a negative sign (I-), the boss is machined with the given pass (step) except the last pass that machines the rest. In either case, the cycle limits the step to the cutting length assigned to the tool in the tool table. Fz Penetration feedrate. F Surface milling feedrate. S Spindle speed. T Roughing tool. If programmed T=0, there is no roughing. D Tool offset. Spindle turning direction (icon). Clockwise. Counterclockwise. Machining direction (icon). Clockwise. Counterclockwise. Programming of M functions. Activating or deactivating the execution of M functions before machining. The cycle allows editing up to 4 M functions. To execute only some of them, define them first and leave the rest of the data unprogrammed. The editor will only show this option if the user has configured the editor to allow programming M functions. Finishing parameters: The finishing operation is carried out in two stages. First, it machines the base of the boss and then the side walls, with tangential entry and exit. The finishing operation defining parameters are: δ Finishing stock on the side walls. δz Finishing stock at the base of the boss. N Number of penetration passes (steps) for the side finishing. If the resulting step is greater than the cutting length assigned to the table in the tool table, the step will be limited to that value. F Surface and side milling feedrate. S Spindle speed. T Finishing tool. If programmed T=0, there is no finishing. 4. CANNED CYCLES OF THE EDITOR Circular boss. CNC 8065 (REF: 1209) ·165·
Page 1 and 2:
CNC 8065 Canned cycles (·M· model
Page 3 and 4:
Canned cycles (·M· model) INDEX A
Page 5 and 6:
Canned cycles (·M· model) ABOUT T
Page 7:
Canned cycles (·M· model) Softwar
Page 11:
Canned cycles (·M· model) VERSION
Page 14 and 15:
CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18:
Canned cycles (·M· model) WARRANT
Page 19:
Canned cycles (·M· model) MATERIA
Page 23 and 24:
MILLING CANNED CYCLES. 1.1 General
Page 25 and 26:
Canned cycles (·M· model) 1.1.1 D
Page 27 and 28:
Canned cycles (·M· model) 1.1.3 P
Page 29 and 30:
Canned cycles (·M· model) Example
Page 31 and 32:
Canned cycles (·M· model) T1 M6 G
Page 33 and 34:
Page 35 and 36:
Canned cycles (·M· model) K Dwell
Page 37 and 38:
Page 39 and 40:
Canned cycles (·M· model) 4 Dwell
Page 41 and 42:
Canned cycles (·M· model) 1.5 G84
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Canned cycles (·M· model) E Dista
Page 49 and 50:
Page 51 and 52:
Canned cycles (·M· model) 3 Rapid
Page 53 and 54:
Page 55 and 56:
Canned cycles (·M· model) 4 Penet
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Canned cycles (·M· model) 7 Rapid
Page 63 and 64:
Canned cycles (·M· model) L Finis
Page 65 and 66:
MULTIPLE MACHINING 2 The programmer
Page 67 and 68:
Canned cycles (·M· model) Basic o
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Canned cycles (·M· model) Y J Y D
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Canned cycles (·M· model) Basic o
Page 81 and 82:
Page 83 and 84:
CYCLE EDITOR 3 The cycle editor is
Page 85 and 86:
Canned cycles (·M· model) 3.1 Con
Page 87 and 88:
Canned cycles (·M· model) 3.3 Sel
Page 89 and 90:
Canned cycles (·M· model) If the
Page 91 and 92:
CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94:
Canned cycles (·M· model) 4.1.2 W
Page 95 and 96:
Canned cycles (·M· model) 4.1.3 V
Page 97 and 98:
Canned cycles (·M· model) 4.2 Cen
Page 99 and 100:
Canned cycles (·M· model) 4.2.1 B
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Canned cycles (·M· model) Spindle
Page 107 and 108:
Canned cycles (·M· model) 4.6 Tap
Page 109 and 110:
Page 111 and 112:
Canned cycles (·M· model) Machini
Page 113 and 114: Canned cycles (·M· model) 4.8 Rea
Page 115 and 116: Canned cycles (·M· model) 4.9 Bor
Page 117 and 118: Canned cycles (·M· model) 4.10 Bo
Page 119 and 120: Canned cycles (·M· model) 4.10.1
Page 121 and 122: Canned cycles (·M· model) I Penet
Page 125 and 126: Canned cycles (·M· model) Type of
Page 127 and 128: Canned cycles (·M· model) θ Pene
Page 129 and 130: Canned cycles (·M· model) 4.13 Ci
Page 131 and 132: Canned cycles (·M· model) The fin
Page 135 and 136: Canned cycles (·M· model) F Surfa
Page 139 and 140: Canned cycles (·M· model) 4.15 2D
Page 141 and 142: Canned cycles (·M· model) T Rough
Page 147 and 148: Canned cycles (·M· model) New pro
Page 149 and 150: Canned cycles (·M· model) P.XY Na
Page 151 and 152: Canned cycles (·M· model) Fz Pene
Page 153 and 154: Canned cycles (·M· model) Program
Page 157 and 158: Canned cycles (·M· model) Configu
Page 159 and 160: Canned cycles (·M· model) 4.17 Re
Page 163: Canned cycles (·M· model) 4.17.1
Page 169 and 170: Canned cycles (·M· model) Z Part
Page 173 and 174: Canned cycles (·M· model) The rou
Page 177 and 178: Canned cycles (·M· model) F Surfa
Page 181 and 182: Canned cycles (·M· model) The rou
Page 185 and 186: Canned cycles (·M· model) 5 Rapid
Page 187 and 188: Canned cycles (·M· model) 4.24 Mu
Page 189 and 190: Canned cycles (·M· model) 4.25 Mu
Page 191 and 192: Canned cycles (·M· model) 4.27 Ra
Page 193 and 194: Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?