4 - Fagor Automation

More documents

Recommendations

Info

1. MILLING CANNED CYCLES. CNC 8065 (REF: 1209) ·54· G88. Circular pocket canned cycle Canned cycles (·M· model) C Milling pass or width. If not programmed or programmed with a 0 value, it assumes a value of 3/4 of the diameter of the selected tool. If it is the same as parameter "J" (pocket radius), it only runs the finishing pass. If programmed with a value greater than the tool diameter, the CNC issues the relevant error message. L Finishing pass. If not programmed or programmed with a 0 value, it does not run the finishing pass. H Feedrate for the finishing pass. If not programmed or programmed with a 0 value, it is carried out at the roughing feedrate. V Tool penetrating feedrate. If not programmed or programmed with a 0 value, it is carried out at 50% of the feedrate in the plane. Basic operation: 1 If the spindle was previously running, it maintains the turning direction. If it is stopped, it starts clockwise (M03). 2 Rapid movement (G0) of the longitudinal axis from the starting plane (Zi) to the reference plane (Z). 3 Rapid movement (G0) of the longitudinal axis up to 1 mm off the part surface. The movement permits, as in the case of the figure, a fast approach to the machining surface when the safety coordinate (Z) is far away from the surface.
Canned cycles (·M· model) 4 Penetration. The longitudinal axis penetrates into the part the distance indicated by "B" and at the feedrate indicated by "V". 5 Milling of the pocket surface at work feedrate in the passes defined by "C" up to a distance "L" (finishing pass) from the pocket wall. It is carried out in the direction indicated by parameter "J". 6 Finishing milling, "L" amount, at the work feedrate defined by "H". In order to obtain good part finish when machining the pocket walls, the finishing passes are carried out with tangential entry and exit. 7 Rapid withdrawal (G0) to the center of the pocket, 1 mm off the machined surface. 8 New milling surfaces until reaching the total depth of the pocket. Penetration, at the feedrate indicated in "F" up to a distance "B" from the previous surface. Milling of the new surface following the steps indicated in points 5, 6 and 7. 9 Withdrawal to the starting plane (Zi) if function G98 is active or to the reference plane (Z) if function G99 is active. 1. MILLING CANNED CYCLES. G88. Circular pocket canned cycle CNC 8065 (REF: 1209) ·55·
Page 1 and 2:
CNC 8065 Canned cycles (·M· model
Page 3 and 4: Canned cycles (·M· model) INDEX A
Page 5 and 6: Canned cycles (·M· model) ABOUT T
Page 7: Canned cycles (·M· model) Softwar
Page 11: Canned cycles (·M· model) VERSION
Page 14 and 15: CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18: Canned cycles (·M· model) WARRANT
Page 19: Canned cycles (·M· model) MATERIA
Page 23 and 24: MILLING CANNED CYCLES. 1.1 General
Page 25 and 26: Canned cycles (·M· model) 1.1.1 D
Page 27 and 28: Canned cycles (·M· model) 1.1.3 P
Page 29 and 30: Canned cycles (·M· model) Example
Page 31 and 32: Canned cycles (·M· model) T1 M6 G
Page 35 and 36: Canned cycles (·M· model) K Dwell
Page 39 and 40: Canned cycles (·M· model) 4 Dwell
Page 41 and 42: Canned cycles (·M· model) 1.5 G84
Page 47 and 48: Canned cycles (·M· model) E Dista
Page 51 and 52: Canned cycles (·M· model) 3 Rapid
Page 53: Canned cycles (·M· model) 1.9 G88
Page 61 and 62: Canned cycles (·M· model) 7 Rapid
Page 63 and 64: Canned cycles (·M· model) L Finis
Page 65 and 66: MULTIPLE MACHINING 2 The programmer
Page 67 and 68: Canned cycles (·M· model) Basic o
Page 73 and 74: Canned cycles (·M· model) Y J Y D
Page 79 and 80: Canned cycles (·M· model) Basic o
Page 83 and 84: CYCLE EDITOR 3 The cycle editor is
Page 85 and 86: Canned cycles (·M· model) 3.1 Con
Page 87 and 88: Canned cycles (·M· model) 3.3 Sel
Page 89 and 90: Canned cycles (·M· model) If the
Page 91 and 92: CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94: Canned cycles (·M· model) 4.1.2 W
Page 95 and 96: Canned cycles (·M· model) 4.1.3 V
Page 97 and 98: Canned cycles (·M· model) 4.2 Cen
Page 99 and 100: Canned cycles (·M· model) 4.2.1 B
Page 105 and 106:
Canned cycles (·M· model) Spindle
Page 107 and 108:
Canned cycles (·M· model) 4.6 Tap
Page 109 and 110:
Canned cycles (·M· model) 4.6.1 B
Page 111 and 112:
Canned cycles (·M· model) Machini
Page 113 and 114:
Canned cycles (·M· model) 4.8 Rea
Page 115 and 116:
Canned cycles (·M· model) 4.9 Bor
Page 117 and 118:
Canned cycles (·M· model) 4.10 Bo
Page 119 and 120:
Canned cycles (·M· model) 4.10.1
Page 121 and 122:
Canned cycles (·M· model) I Penet
Page 123 and 124:
Page 125 and 126:
Canned cycles (·M· model) Type of
Page 127 and 128:
Canned cycles (·M· model) θ Pene
Page 129 and 130:
Canned cycles (·M· model) 4.13 Ci
Page 131 and 132:
Canned cycles (·M· model) The fin
Page 133 and 134:
Page 135 and 136:
Canned cycles (·M· model) F Surfa
Page 137 and 138:
Page 139 and 140:
Canned cycles (·M· model) 4.15 2D
Page 141 and 142:
Canned cycles (·M· model) T Rough
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Canned cycles (·M· model) New pro
Page 149 and 150:
Canned cycles (·M· model) P.XY Na
Page 151 and 152:
Canned cycles (·M· model) Fz Pene
Page 153 and 154:
Canned cycles (·M· model) Program
Page 155 and 156:
Page 157 and 158:
Canned cycles (·M· model) Configu
Page 159 and 160:
Canned cycles (·M· model) 4.17 Re
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Canned cycles (·M· model) I Penet
Page 167 and 168:
Page 169 and 170:
Canned cycles (·M· model) Z Part
Page 171 and 172:
Page 173 and 174:
Canned cycles (·M· model) The rou
Page 175 and 176:
Page 177 and 178:
Canned cycles (·M· model) F Surfa
Page 179 and 180:
Page 181 and 182:
Canned cycles (·M· model) The rou
Page 183 and 184:
Page 185 and 186:
Canned cycles (·M· model) 5 Rapid
Page 187 and 188:
Canned cycles (·M· model) 4.24 Mu
Page 189 and 190:
Canned cycles (·M· model) 4.25 Mu
Page 191 and 192:
Canned cycles (·M· model) 4.27 Ra
Page 193 and 194:
Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?