4 - Fagor Automation

More documents

Recommendations

Info

1. MILLING CANNED CYCLES. CNC 8065 (REF: 1209) ·32· G81. Drilling canned cycle 1.2 G81. Drilling canned cycle Programming format in Cartesian coordinates: Parameter definition: G81 Z I K A Canned cycles (·M· model) Z Reference plane. In G90, coordinate referred to part zero. In G91, coordinate referred to starting plane (Zi). If not programmed, it assumes as reference plane the current position of the tool (Z=Zi). I Drilling depth. In G90, coordinate referred to part zero. In G91, coordinate referred to reference plane (Z). K Delay, in seconds, between the drilling and the withdrawal movement. If not programmed, it assumes K0. A Spindle behavior when going into the hole and coming out of it. A0: The tool goes into the hole and comes out turning. A1: The tool goes into the hole turning and comes out stopped. If not programmed, it assumes a value of A0. Basic operation: 1 If the spindle was previously running, it maintains the turning direction. If it is stopped, it starts clockwise (M03). 2 Rapid movement (G0) of the longitudinal axis from the starting plane (Zi) to the reference plane (Z). 3 Drill the hole. Movement of the longitudinal axis at work feedrate, to the bottom of the hole programmed in "I". 4 Dwell, in seconds, if it has been programmed. 5 Rapid withdrawal (G0) to the starting plane (Zi) if function G98 is active or to the reference plane (Z) if function G99 is active. The spindle will come out turning or stopped depending on parameter "A".
Canned cycles (·M· model) 1.2.1 Programming example Absolute programming: T1 D1 M6 S1000 M3 M8 M41 G0 G90 X0 Y0 Z25 F200 N10 G99 X15 Y15 G81 Z2 I-20 N20 X85 N30 Y85 N40 G98 X15 M30 Incremental programming: T1 D1 M6 S1000 M3 M8 M41 G0 G90 X0 Y0 Z25 F200 N10 G99 G91 X15 Y15 G81 Z-23 I-22 N20 X70 N30 Y70 N40 G98 X-70 M30 1. MILLING CANNED CYCLES. G81. Drilling canned cycle CNC 8065 (REF: 1209) ·33·
Page 1 and 2: CNC 8065 Canned cycles (·M· model
Page 3 and 4: Canned cycles (·M· model) INDEX A
Page 5 and 6: Canned cycles (·M· model) ABOUT T
Page 7: Canned cycles (·M· model) Softwar
Page 11: Canned cycles (·M· model) VERSION
Page 14 and 15: CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18: Canned cycles (·M· model) WARRANT
Page 19: Canned cycles (·M· model) MATERIA
Page 23 and 24: MILLING CANNED CYCLES. 1.1 General
Page 25 and 26: Canned cycles (·M· model) 1.1.1 D
Page 27 and 28: Canned cycles (·M· model) 1.1.3 P
Page 29 and 30: Canned cycles (·M· model) Example
Page 31: Canned cycles (·M· model) T1 M6 G
Page 35 and 36: Canned cycles (·M· model) K Dwell
Page 39 and 40: Canned cycles (·M· model) 4 Dwell
Page 41 and 42: Canned cycles (·M· model) 1.5 G84
Page 47 and 48: Canned cycles (·M· model) E Dista
Page 51 and 52: Canned cycles (·M· model) 3 Rapid
Page 55 and 56: Canned cycles (·M· model) 4 Penet
Page 61 and 62: Canned cycles (·M· model) 7 Rapid
Page 63 and 64: Canned cycles (·M· model) L Finis
Page 65 and 66: MULTIPLE MACHINING 2 The programmer
Page 67 and 68: Canned cycles (·M· model) Basic o
Page 73 and 74: Canned cycles (·M· model) Y J Y D
Page 79 and 80: Canned cycles (·M· model) Basic o
Page 83 and 84:
CYCLE EDITOR 3 The cycle editor is
Page 85 and 86:
Canned cycles (·M· model) 3.1 Con
Page 87 and 88:
Canned cycles (·M· model) 3.3 Sel
Page 89 and 90:
Canned cycles (·M· model) If the
Page 91 and 92:
CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94:
Canned cycles (·M· model) 4.1.2 W
Page 95 and 96:
Canned cycles (·M· model) 4.1.3 V
Page 97 and 98:
Canned cycles (·M· model) 4.2 Cen
Page 99 and 100:
Canned cycles (·M· model) 4.2.1 B
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Canned cycles (·M· model) Spindle
Page 107 and 108:
Canned cycles (·M· model) 4.6 Tap
Page 109 and 110:
Page 111 and 112:
Canned cycles (·M· model) Machini
Page 113 and 114:
Canned cycles (·M· model) 4.8 Rea
Page 115 and 116:
Canned cycles (·M· model) 4.9 Bor
Page 117 and 118:
Canned cycles (·M· model) 4.10 Bo
Page 119 and 120:
Canned cycles (·M· model) 4.10.1
Page 121 and 122:
Canned cycles (·M· model) I Penet
Page 123 and 124:
Page 125 and 126:
Canned cycles (·M· model) Type of
Page 127 and 128:
Canned cycles (·M· model) θ Pene
Page 129 and 130:
Canned cycles (·M· model) 4.13 Ci
Page 131 and 132:
Canned cycles (·M· model) The fin
Page 133 and 134:
Page 135 and 136:
Canned cycles (·M· model) F Surfa
Page 137 and 138:
Page 139 and 140:
Canned cycles (·M· model) 4.15 2D
Page 141 and 142:
Canned cycles (·M· model) T Rough
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Canned cycles (·M· model) New pro
Page 149 and 150:
Canned cycles (·M· model) P.XY Na
Page 151 and 152:
Canned cycles (·M· model) Fz Pene
Page 153 and 154:
Canned cycles (·M· model) Program
Page 155 and 156:
Page 157 and 158:
Canned cycles (·M· model) Configu
Page 159 and 160:
Canned cycles (·M· model) 4.17 Re
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Canned cycles (·M· model) I Penet
Page 167 and 168:
Page 169 and 170:
Canned cycles (·M· model) Z Part
Page 171 and 172:
Page 173 and 174:
Canned cycles (·M· model) The rou
Page 175 and 176:
Page 177 and 178:
Canned cycles (·M· model) F Surfa
Page 179 and 180:
Page 181 and 182:
Canned cycles (·M· model) The rou
Page 183 and 184:
Page 185 and 186:
Canned cycles (·M· model) 5 Rapid
Page 187 and 188:
Canned cycles (·M· model) 4.24 Mu
Page 189 and 190:
Canned cycles (·M· model) 4.25 Mu
Page 191 and 192:
Canned cycles (·M· model) 4.27 Ra
Page 193 and 194:
Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?