4 - Fagor Automation

More documents

Recommendations

Info

3. CYCLE EDITOR CNC 8065 ·88· Simulate a canned cycle. (REF: 1209) 3.4 Simulate a canned cycle. i Canned cycles (·M· model) With the canned cycle editor, it is possible to simulate the cycle being edited without having to simulate the whole part-program. During simulation, the editor allows viewing and editing another canned cycle and also returning to the program editor. If the cycle editor is included in the automatic operating mode, it will not be possible to simulate a cycle. Simulating a cycle Pressing the [START] icon begins the simulation of the cycle that is being edited. The simulation may be interrupted with the [STOP] icon or canceled with the [RESET] icon. START STOP RESET The simulation graphics is always superimposed on the help graphics of the main cycle. If the cycle has a positioning associated with it, the graphics is superimposed on the main cycle; in the case of a 2D pocket with drilling, on the pocket. Once the simulation has started, it is maintained until the cycle is over or the [RESET] icon is pressed. Even when changing cycles or returning to the program editor during simulation, the previous cycle is still in effect during the simulation. Cycle simulation window The graphics window (in simulation) is activated by pressing the [START] icon and is canceled by pressing the [RESET] icon. This window is placed over the cycle help graphics; it may be expanded to full screen (or shrunk again) using the key combination [CTRL]+[G]. The lower left corner of the window indicates the name of the cycle and the simulation channel, which will be the channel of the program editor from which the cycle editor has been called. Configuring the graphic environment When activating or selecting the graphics window, the horizontal softkey menu shows the available graphic options. For further information on the graphic options, see the chapter on the edit-simulation mode of the operation manual. Some graphic options can also be edited manually. The editing area is only shown when the window is expanded ([CTRL]+[G]). The simulated graphics are maintained until erased; i.e. starting to simulate a new cycle does not erase the previous graphics. Best area for displaying the graphics The display area may be established from the softkey menu associated with the simulation graphics window or may be left up to the CNC to periodically calculate the best area. While the graphics window is visible, the key combination [CTRL]+[D] activates the calculation of the best area. From that moment on and until quitting the cycle editor, the CNC periodically calculates the best display are for the graphics. When quitting the graphics, it will assume as the new display area the one calculated last. Window for simulation and data editing While the graphics window is selected, it may be switched to the cycle parameter area using the direct access keys. If the parameter belongs to a positioning cycle, firs press [CTRL]+[F2] (window change)
Canned cycles (·M· model) If the cycle is simulated at full screen, the cycle editor may also be accessed by pressing the [ESC] key. To select the graphics window again, use the key combination [CTRL]+[G] or [SHIFT]+[G] or [G]. The horizontal softkey menu will show the graphic options when the graphics window has the focus and those of the cycle editor if otherwise. The simulation in progress is not interrupted while editing data. If the cycle data is changed during simulation, they will be assumed for the next simulation of the cycle; i.e. after RESETting the simulation in progress once it has finished or after a STOP and RESET to abort it. Summary of the hotkeys while simulating a cycle. [CTRL] + [F2] In the parameter window, it toggles between the cycle parameters and the positioning parameters. [CTRL]+[G] It selects the graphics window. It shrinks or expands the graphics window. It shows the dialog area for the graphics data. [CTRL]+[D] It activates the periodic calculation of the best display area. [SHIFT]+[G] [G] It shows the graphics window when a simulation is running and the parameter editing window is active. [ESC] If the graphics are shown at full screen, it shows the cycle editor screen. 3. CYCLE EDITOR Simulate a canned cycle. CNC 8065 (REF: 1209) ·89·
Page 1 and 2:
CNC 8065 Canned cycles (·M· model
Page 3 and 4:
Canned cycles (·M· model) INDEX A
Page 5 and 6:
Canned cycles (·M· model) ABOUT T
Page 7:
Canned cycles (·M· model) Softwar
Page 11:
Canned cycles (·M· model) VERSION
Page 14 and 15:
CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18:
Canned cycles (·M· model) WARRANT
Page 19:
Canned cycles (·M· model) MATERIA
Page 23 and 24:
MILLING CANNED CYCLES. 1.1 General
Page 25 and 26:
Canned cycles (·M· model) 1.1.1 D
Page 27 and 28:
Canned cycles (·M· model) 1.1.3 P
Page 29 and 30:
Canned cycles (·M· model) Example
Page 31 and 32:
Canned cycles (·M· model) T1 M6 G
Page 33 and 34:
Canned cycles (·M· model) 1.2.1 P
Page 35 and 36:
Canned cycles (·M· model) K Dwell
Page 37 and 38: Canned cycles (·M· model) 1.3.1 P
Page 39 and 40: Canned cycles (·M· model) 4 Dwell
Page 41 and 42: Canned cycles (·M· model) 1.5 G84
Page 47 and 48: Canned cycles (·M· model) E Dista
Page 51 and 52: Canned cycles (·M· model) 3 Rapid
Page 55 and 56: Canned cycles (·M· model) 4 Penet
Page 61 and 62: Canned cycles (·M· model) 7 Rapid
Page 63 and 64: Canned cycles (·M· model) L Finis
Page 65 and 66: MULTIPLE MACHINING 2 The programmer
Page 67 and 68: Canned cycles (·M· model) Basic o
Page 73 and 74: Canned cycles (·M· model) Y J Y D
Page 79 and 80: Canned cycles (·M· model) Basic o
Page 83 and 84: CYCLE EDITOR 3 The cycle editor is
Page 85 and 86: Canned cycles (·M· model) 3.1 Con
Page 87: Canned cycles (·M· model) 3.3 Sel
Page 91 and 92: CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94: Canned cycles (·M· model) 4.1.2 W
Page 95 and 96: Canned cycles (·M· model) 4.1.3 V
Page 97 and 98: Canned cycles (·M· model) 4.2 Cen
Page 99 and 100: Canned cycles (·M· model) 4.2.1 B
Page 105 and 106: Canned cycles (·M· model) Spindle
Page 107 and 108: Canned cycles (·M· model) 4.6 Tap
Page 111 and 112: Canned cycles (·M· model) Machini
Page 113 and 114: Canned cycles (·M· model) 4.8 Rea
Page 115 and 116: Canned cycles (·M· model) 4.9 Bor
Page 117 and 118: Canned cycles (·M· model) 4.10 Bo
Page 119 and 120: Canned cycles (·M· model) 4.10.1
Page 121 and 122: Canned cycles (·M· model) I Penet
Page 125 and 126: Canned cycles (·M· model) Type of
Page 127 and 128: Canned cycles (·M· model) θ Pene
Page 129 and 130: Canned cycles (·M· model) 4.13 Ci
Page 131 and 132: Canned cycles (·M· model) The fin
Page 135 and 136: Canned cycles (·M· model) F Surfa
Page 139 and 140:
Canned cycles (·M· model) 4.15 2D
Page 141 and 142:
Canned cycles (·M· model) T Rough
Page 143 and 144:
Canned cycles (·M· model) 4.15.1
Page 145 and 146:
Page 147 and 148:
Canned cycles (·M· model) New pro
Page 149 and 150:
Canned cycles (·M· model) P.XY Na
Page 151 and 152:
Canned cycles (·M· model) Fz Pene
Page 153 and 154:
Canned cycles (·M· model) Program
Page 155 and 156:
Page 157 and 158:
Canned cycles (·M· model) Configu
Page 159 and 160:
Canned cycles (·M· model) 4.17 Re
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Canned cycles (·M· model) I Penet
Page 167 and 168:
Page 169 and 170:
Canned cycles (·M· model) Z Part
Page 171 and 172:
Page 173 and 174:
Canned cycles (·M· model) The rou
Page 175 and 176:
Page 177 and 178:
Canned cycles (·M· model) F Surfa
Page 179 and 180:
Page 181 and 182:
Canned cycles (·M· model) The rou
Page 183 and 184:
Page 185 and 186:
Canned cycles (·M· model) 5 Rapid
Page 187 and 188:
Canned cycles (·M· model) 4.24 Mu
Page 189 and 190:
Canned cycles (·M· model) 4.25 Mu
Page 191 and 192:
Canned cycles (·M· model) 4.27 Ra
Page 193 and 194:
Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?