4 - Fagor Automation

More documents

Recommendations

Info

Canned cycles (·M· model) DECLARATION OF CONFORMITY The manufacturer: <strong>Fagor</strong> <strong>Automation</strong> S. Coop. Barrio de San Andrés Nº 19, C.P.20500, Mondragón -Guipúzcoa- (Spain). Declares: The manufacturer declares under their exclusive responsibility the conformity of the product: 8065 CNC Consisting of the following modules and accessories: 8065-M-ICU 8065-T-ICU MONITOR-LCD-10, MONITOR-LCD-15 HORIZONTAL-KEYB, VERTICAL-KEYB, OP-PANEL BATTERY Remote Modules RIOW, RIO5, RIO70 Note.Some additional characters may follow the model references indicated above. They all comply with the directives listed here. However, compliance may be verified on the label of the unit itself. Referred to by this declaration with following directives: Low-voltage regulations. EN 60204-1: 2006 Electrical equipment on machines — Part1. General requirements. Regulation on electromagnetic compatibility. EN 61131-2: 2007 PLC — Part 2. Equipment requirements and tests. According to the European Community Directives 2006/95/EC on Low Voltage and 2004/108/EC on Electromagnetic Compatibility and their updates. In Mondragón, October 1st 2011. CNC 8065 (REF: 1209) ·9·
Page 1 and 2: CNC 8065 Canned cycles (·M· model
Page 3 and 4: Canned cycles (·M· model) INDEX A
Page 5 and 6: Canned cycles (·M· model) ABOUT T
Page 7: Canned cycles (·M· model) Softwar
Page 13 and 14: Canned cycles (·M· model) SAFETY
Page 15: Canned cycles (·M· model) Symbols
Page 18 and 19: CNC 8065 (REF: 1209) ·18· WARRANT
Page 21: Canned cycles (·M· model) CNC MAI
Page 24 and 25: 1. MILLING CANNED CYCLES. General c
Page 32 and 33: 1. MILLING CANNED CYCLES. CNC 8065
Page 58 and 59:
1. MILLING CANNED CYCLES. CNC 8065
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
2. MULTIPLE MACHINING CNC 8065 (REF
Page 68 and 69:
2. MULTIPLE MACHINING CNC 8065 ·68
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
3. CYCLE EDITOR CNC 8065 (REF: 1209
Page 86 and 87:
3. CYCLE EDITOR CNC 8065 (REF: 1209
Page 88 and 89:
3. CYCLE EDITOR CNC 8065 ·88· Sim
Page 90 and 91:
3. CYCLE EDITOR CNC 8065 ·90· Sim
Page 92 and 93:
4. CANNED CYCLES OF THE EDITOR CNC
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
4. CANNED CYCLES OF THE EDITOR Cent
Page 100 and 101:
4. CANNED CYCLES OF THE EDITOR Dril
Page 102 and 103:
4. CANNED CYCLES OF THE EDITOR Deep
Page 104 and 105:
4. CANNED CYCLES OF THE EDITOR Bore
Page 106 and 107:
4. CANNED CYCLES OF THE EDITOR Bore
Page 108 and 109:
4. CANNED CYCLES OF THE EDITOR Tapp
Page 110 and 111:
4. CANNED CYCLES OF THE EDITOR Thre
Page 112 and 113:
4. CANNED CYCLES OF THE EDITOR Thre
Page 114 and 115:
4. CANNED CYCLES OF THE EDITOR Ream
Page 116 and 117:
4. CANNED CYCLES OF THE EDITOR Bori
Page 118 and 119:
Page 120 and 121:
4. CANNED CYCLES OF THE EDITOR Simp
Page 122 and 123:
4. CANNED CYCLES OF THE EDITOR Simp
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
4. CANNED CYCLES OF THE EDITOR Circ
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
4. CANNED CYCLES OF THE EDITOR 2D p
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
4. CANNED CYCLES OF THE EDITOR Rect
Page 162 and 163:
4. CANNED CYCLES OF THE EDITOR Rect
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
4. CANNED CYCLES OF THE EDITOR Surf
Page 170 and 171:
4. CANNED CYCLES OF THE EDITOR Surf
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
4. CANNED CYCLES OF THE EDITOR Free
Page 178 and 179:
4. CANNED CYCLES OF THE EDITOR Free
Page 180 and 181:
4. CANNED CYCLES OF THE EDITOR Slot
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
4. CANNED CYCLES OF THE EDITOR Rand
Page 194:
CNC 8065 (REF: 1209) ·194· Canned
show all

4 - Fagor Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?