4 - Fagor Automation

More documents

Recommendations

Info

3. CYCLE EDITOR CNC 8065 (REF: 1209) ·86· Teach-in mode. 3.2 Teach-in mode. Canned cycles (·M· model) The "+" softkey shows the softkey to activate the teach-in mode that allows jogging the axes of the machine and entering the actual (real) position of the axes into the data. The reset of the data must be edited manually. Being this mode active, the bottom of the cycle editor shows a window with the actual axis position and the active machining conditions. The information in the window cannot be configured, it is not conditioned by the configuration made in the EDISIMU mode for the teach-in mode. When teach-in mode is active, it is possible to keep editing the data of the axes directly from the keyboard or they may be assigned the actual position of the axes. Both editing methods may be used indistinctly, even while defining a cycle. To assign the position of its axis to a data, proceed as follows: 1 Select one of the data with the cursor. 2 Move the axes to the desired position using the jog keys, the handwheels or the MDI/MDA mode. 3 Press the [RECALL] key. The editor enters the actual position of the corresponding axis into the selected data.
Canned cycles (·M· model) 3.3 Selecting data, profiles and icons Data selection. To enter or modify a data, it must be selected; i.e. it must have the editing focus on it. The parameters of the cycles may be selected with the [] [] [] [] keys or with the direct access keys. The first data of each group may also be selected by pressing the page-up and page-down keys. The direct access keys correspond to the name of the parameters; [F] for feedrates, [T] for tools, etc. Every time the same key is pressed, it selects the next data of the same type. Data entry. Place the cursor in the corresponding window, key in the desired value and press [ENTER]. If [ENTER] is not pressed, the new value will not be assumed. If the Teach-in mode is selected, the current position of the machine may be associated with a coordinate. Place the cursor in the relevant window and press the [RECALL] key. For the X axis parameters, it will take the coordinate of the first axis of the channel where the edit-simulation mode is active. For the Y axis parameters, the coordinate of the second axis and for the Z axis parameters, the coordinate of the third one. Changing the state of an icon. Place the cursor on the desired icon and press the space bar. Select - Define a profile. To select or modify a profile, the corresponding data must be selected; i.e. it must have the editing focus on it. To select an existing profile, press the [] key to expand the list of defined profiles and select one or type its name. To define a new profile, write the desired name and press the [RECALL] key to access the profile editor. To modify an existing profile, select it from the list or write its desired name and press the [RECALL] key to access the profile editor. To delete a profile, press the [] key to expand (drop) the list of profiles and select one. Press the [DEL] key to delete it. 3. CYCLE EDITOR Selecting data, profiles and icons CNC 8065 (REF: 1209) ·87·
Page 1 and 2:
CNC 8065 Canned cycles (·M· model
Page 3 and 4:
Canned cycles (·M· model) INDEX A
Page 5 and 6:
Canned cycles (·M· model) ABOUT T
Page 7:
Canned cycles (·M· model) Softwar
Page 11:
Canned cycles (·M· model) VERSION
Page 14 and 15:
CNC 8065 (REF: 1209) ·14· PRECAUT
Page 17 and 18:
Canned cycles (·M· model) WARRANT
Page 19:
Canned cycles (·M· model) MATERIA
Page 23 and 24:
MILLING CANNED CYCLES. 1.1 General
Page 25 and 26:
Canned cycles (·M· model) 1.1.1 D
Page 27 and 28:
Canned cycles (·M· model) 1.1.3 P
Page 29 and 30:
Canned cycles (·M· model) Example
Page 31 and 32:
Canned cycles (·M· model) T1 M6 G
Page 33 and 34:
Canned cycles (·M· model) 1.2.1 P
Page 35 and 36: Canned cycles (·M· model) K Dwell
Page 37 and 38: Canned cycles (·M· model) 1.3.1 P
Page 39 and 40: Canned cycles (·M· model) 4 Dwell
Page 41 and 42: Canned cycles (·M· model) 1.5 G84
Page 47 and 48: Canned cycles (·M· model) E Dista
Page 51 and 52: Canned cycles (·M· model) 3 Rapid
Page 55 and 56: Canned cycles (·M· model) 4 Penet
Page 61 and 62: Canned cycles (·M· model) 7 Rapid
Page 63 and 64: Canned cycles (·M· model) L Finis
Page 65 and 66: MULTIPLE MACHINING 2 The programmer
Page 67 and 68: Canned cycles (·M· model) Basic o
Page 73 and 74: Canned cycles (·M· model) Y J Y D
Page 79 and 80: Canned cycles (·M· model) Basic o
Page 83 and 84: CYCLE EDITOR 3 The cycle editor is
Page 85: Canned cycles (·M· model) 3.1 Con
Page 89 and 90: Canned cycles (·M· model) If the
Page 91 and 92: CANNED CYCLES OF THE EDITOR 4.1 Can
Page 93 and 94: Canned cycles (·M· model) 4.1.2 W
Page 95 and 96: Canned cycles (·M· model) 4.1.3 V
Page 97 and 98: Canned cycles (·M· model) 4.2 Cen
Page 99 and 100: Canned cycles (·M· model) 4.2.1 B
Page 105 and 106: Canned cycles (·M· model) Spindle
Page 107 and 108: Canned cycles (·M· model) 4.6 Tap
Page 111 and 112: Canned cycles (·M· model) Machini
Page 113 and 114: Canned cycles (·M· model) 4.8 Rea
Page 115 and 116: Canned cycles (·M· model) 4.9 Bor
Page 117 and 118: Canned cycles (·M· model) 4.10 Bo
Page 119 and 120: Canned cycles (·M· model) 4.10.1
Page 121 and 122: Canned cycles (·M· model) I Penet
Page 125 and 126: Canned cycles (·M· model) Type of
Page 127 and 128: Canned cycles (·M· model) θ Pene
Page 129 and 130: Canned cycles (·M· model) 4.13 Ci
Page 131 and 132: Canned cycles (·M· model) The fin
Page 135 and 136: Canned cycles (·M· model) F Surfa
Page 137 and 138:
Canned cycles (·M· model) 4.14.1
Page 139 and 140:
Canned cycles (·M· model) 4.15 2D
Page 141 and 142:
Canned cycles (·M· model) T Rough
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Canned cycles (·M· model) New pro
Page 149 and 150:
Canned cycles (·M· model) P.XY Na
Page 151 and 152:
Canned cycles (·M· model) Fz Pene
Page 153 and 154:
Canned cycles (·M· model) Program
Page 155 and 156:
Page 157 and 158:
Canned cycles (·M· model) Configu
Page 159 and 160:
Canned cycles (·M· model) 4.17 Re
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Canned cycles (·M· model) I Penet
Page 167 and 168:
Page 169 and 170:
Canned cycles (·M· model) Z Part
Page 171 and 172:
Page 173 and 174:
Canned cycles (·M· model) The rou
Page 175 and 176:
Page 177 and 178:
Canned cycles (·M· model) F Surfa
Page 179 and 180:
Page 181 and 182:
Canned cycles (·M· model) The rou
Page 183 and 184:
Page 185 and 186:
Canned cycles (·M· model) 5 Rapid
Page 187 and 188:
Canned cycles (·M· model) 4.24 Mu
Page 189 and 190:
Canned cycles (·M· model) 4.25 Mu
Page 191 and 192:
Canned cycles (·M· model) 4.27 Ra
Page 193 and 194:
Canned cycles (·M· model) CNC 806
show all

4 - Fagor Automation

Create successful ePaper yourself

Delete template?

Save as template?