NPL-352 Manual-09.pdf

More documents

Recommendations

Info

4 Applications Using [DSP] to switch between display screens Press [DSP] to switch between the Stakeout display screens. The following screens are available: ARC1 ARC2 ARC3 ARC4 Sta O/S dZ X Y Z HA VA SD HA VD HD ARC5 HD VD SD The ARC5 screen is only available if the secondary distance unit is set. For more information, see Others settings, page 140. Every time you press [DSP], the next screen appears. If you press [DSP] in the last screen (ARC4 or ARC5), the ARC1 screen appears. To record the point, press [ENT] on any observation screen. The arc is stored in comment records. Sample records CO,Arc P1:583 AZ1=0.0000 P2:102 CO, AZ2=311.2932 Radius=50.0000 Length=125.6637 CO, Sta= -12.6876 Offset= 1.3721 dZ= 0.0971 SS,17,1.0000,6.9202,18.4700,80.3120,15:48:48,2REF-LINE 94 Pulse Laser Station NPL-302 Series Instruction Manual
Applications 4 Remote distance measurement 40.1 This function measures the horizontal distance, vertical distance, and slope distance between two points. 2nd sighting point 1st sighting point rSD rVD rHD Horizontal angle 0 direction 2nd sighting point rHA 1st sighting point Station point rSD Slope distance between two points rHD Horizontal distance between two points rVD Vertical distance between two points rV% Percentage of grade (rVD/rHD) × 100% rGD Vertical grade (rHD/rVD) :1 rAZ Azimuth from first point to second point Pulse Laser Station NPL-302 Series Instruction Manual 95
Page 1 and 2:
Pulse Laser Station NPL-302 Series
Page 3:
Taiwan Battery Recycling Requiremen
Page 6 and 7:
Safety Introduction For your safety
Page 8 and 9:
Safety Warnings and Cautions The fo
Page 10 and 11:
Safety Cautions Before using the in
Page 12 and 13:
Safety xii Pulse Laser Station NPL-
Page 14 and 15:
Contents Adjusting the height of th
Page 16 and 17:
Contents Program Key. . . . . . . .
Page 18 and 19:
Contents Downloading data . . . . .
Page 20 and 21:
Contents 10 Error Messages . . . .
Page 22 and 23:
1 Introduction Welcome 1.1 Thank yo
Page 24 and 25:
1 Introduction Parts of the Instrum
Page 26 and 27:
1 Introduction Maintenance 1.3 Befo
Page 28 and 29:
1 Introduction 8 Pulse Laser Statio
Page 30 and 31:
2 Preparation Unpacking and Packing
Page 32 and 33:
2 Preparation • To prevent malfun
Page 34 and 35:
2 Preparation Attaching the BC-65 b
Page 36 and 37:
2 Preparation When the instrument i
Page 38 and 39:
2 Preparation d. If the target imag
Page 40 and 41:
2 Preparation Measurable distances
Page 42 and 43:
2 Preparation Setting Up the Prism
Page 44 and 45:
2 Preparation Note - The prism cons
Page 46 and 47:
2 Preparation 26 Pulse Laser Statio
Page 48 and 49:
3 Getting Started Turning the Instr
Page 50 and 51:
3 Getting Started Selecting a Langu
Page 52 and 53:
3 Getting Started Table 3.1 Regiona
Page 54 and 55:
3 Getting Started Table 3.2 summari
Page 56 and 57:
3 Getting Started Table 3.2 Key fun
Page 58 and 59:
3 Getting Started Adjusting lightin
Page 60 and 61:
3 Getting Started Customizing items
Page 62 and 63:
3 Getting Started 3. If you have se
Page 64 and 65: 3 Getting Started To change the set
Page 66 and 67: 3 Getting Started [USR] keys 30.4 I
Page 68 and 69: 3 Getting Started When you select a
Page 70 and 71: 3 Getting Started Entering a new po
Page 72 and 73: 3 Getting Started Entering a point
Page 74 and 75: 3 Getting Started A layer has an ar
Page 76 and 77: 3 Getting Started The following exa
Page 78 and 79: 3 Getting Started Jobs created befo
Page 80 and 81: 3 Getting Started If the signal lev
Page 82 and 83: 3 Getting Started 62 Pulse Laser St
Page 84 and 85: 4 Applications HA Reset and Angle O
Page 86 and 87: 4 Applications If you have already
Page 88 and 89: 4 Applications Sighting the backsig
Page 90 and 91: 4 Applications Sighting the backsig
Page 92 and 93: 4 Applications 1. To start the rese
Page 94 and 95: 4 Applications 12. Select the BS po
Page 96 and 97: 4 Applications Determining station
Page 98 and 99: 4 Applications Base XYZ function: B
Page 100 and 101: 4 Applications After the measuremen
Page 102 and 103: 4 Applications If you press [ENT] w
Page 104 and 105: 4 Applications Specifying the stake
Page 106 and 107: 4 Applications Advanced feature: Sp
Page 108 and 109: 4 Applications For example, if you
Page 110 and 111: 4 Applications Program Key 4.1 To d
Page 112 and 113: 4 Applications To store the point a
Page 116 and 117: 4 Applications Measuring between th
Page 118 and 119: 4 Applications Measuring remote ele
Page 120 and 121: 4 Applications 4. Enter a value in
Page 122 and 123: 4 Applications If the plane is defi
Page 124 and 125: 4 Applications Outputting data to t
Page 126 and 127: 4 Applications You can enter any co
Page 128 and 129: 4 Applications Extending a line by
Page 130 and 131: 4 Applications Entering a horizonta
Page 132 and 133: 4 Applications 7. Enter a PT (and C
Page 134 and 135: 4 Applications Extending the slope
Page 136 and 137: 5 Menu Key Introduction 5.1 Use the
Page 138 and 139: 5 Menu Key If you select US-Ft or I
Page 140 and 141: 5 Menu Key Displaying job Informati
Page 142 and 143: 5 Menu Key 3. Enter the second poin
Page 144 and 145: 5 Menu Key Traverse To open the Tra
Page 146 and 147: 5 Menu Key If you enter a new point
Page 148 and 149: 5 Menu Key Specify the azimuth bear
Page 150 and 151: 5 Menu Key 4. To define the line by
Page 152 and 153: 5 Menu Key Calculating a distance-d
Page 154 and 155: 5 Menu Key Advanced feature: Enteri
Page 156 and 157: 5 Menu Key Distance 51.2 To open th
Page 158 and 159: 5 Menu Key Coordinate 51.3 To open
Page 160 and 161: 5 Menu Key Others settings 51.9 To
Page 162 and 163: 5 Menu Key To see detailed informat
Page 164 and 165:
5 Menu Key AR records An AR record
Page 166 and 167:
5 Menu Key Deleting records 52.2 De
Page 168 and 169:
5 Menu Key All observations from th
Page 170 and 171:
5 Menu Key 2. Use [^] or [v] to hig
Page 172 and 173:
5 Menu Key If you selected ST, SO,
Page 174 and 175:
5 Menu Key Entering coordinates 50.
Page 176 and 177:
5 Menu Key To delete a whole layer,
Page 178 and 179:
5 Menu Key The point name is added
Page 180 and 181:
5 Menu Key Downloading data 51.1 To
Page 182 and 183:
5 Menu Key Advanced feature: Editin
Page 184 and 185:
5 Menu Key There are two [MSR] keys
Page 186 and 187:
5 Menu Key [DAT] key settings 51.5
Page 188 and 189:
5 Menu Key 168 Pulse Laser Station
Page 190 and 191:
6 Checking and Adjustment Checking
Page 192 and 193:
6 Checking and Adjustment Zero Poin
Page 194 and 195:
6 Checking and Adjustment Checking
Page 196 and 197:
6 Checking and Adjustment 176 Pulse
Page 198 and 199:
7 Specifications Main Body 7.1 Tele
Page 200 and 201:
7 Specifications Measurement interv
Page 202 and 203:
7 Specifications Environmental perf
Page 204 and 205:
7 Specifications To connect to an e
Page 206 and 207:
8 System Diagrams System Components
Page 208 and 209:
8 System Diagrams 188 Pulse Laser S
Page 210 and 211:
9 Communications Uploading Coordina
Page 212 and 213:
9 Communications File format 92.2 P
Page 214 and 215:
9 Communications Downloading Data 9
Page 216 and 217:
9 Communications Stakeout records S
Page 218 and 219:
9 Communications Instrument record
Page 220 and 221:
9 Communications Observation record
Page 222 and 223:
9 Communications Data examples 93.4
Page 224 and 225:
9 Communications SDR2x coordinate d
Page 226 and 227:
10 Error Messages Angle 10.1 STN Se
Page 228 and 229:
10 Error Messages DELETE Stn-XYZ 10
Page 230 and 231:
10 Error Messages Recording Data 10
Page 232 and 233:
10 Error Messages Settings 10.11 Jo
Page 234:
10 Error Messages Z-coordinate is r
show all

NPL-352 Manual-09.pdf

Create successful ePaper yourself

Delete template?

Save as template?