CSDP Plus Servo Drive User Manual

More documents

Recommendations

Info

If the torque gain is 100%/3V and the input voltage is 3V, 100% torque, rated torque, will be generated. If the torque command gain is 100%/3V and the input voltage is 9 V, 300% torque, the maximum torque of the motor, will be generated. SEt-06 Torque Command Filter • Setting range: 0 to 60000 rad/s • User Default: 1800 • Changes anytime This parameter limits the high frequency element of the torque command. The set value changes according to the rigidity of the load. Torque filter cut-off frequency lowers the frequency depending on how many delay factors there were during the process of delivering the motor’s torque to the load. In the case of a directly-coupled disk with no delay factor, a value that is too low can cause vibration. Contrastingly, if the value is set too high for a belt or chain with many delay factors, there can be a vibration. Finish the setting according to the type of the load by referring to the next table. Torque Filter Cut-off Frequency Load Type Directly-coupled Disk 4000 Ball Screw coupled directly 2000 to 3000 Belt or Chain 500 to 1000 Recommended Value 136
SEt-07 Position Feedforward Filter • Setting range: 0 to 5000 rad/s • User Default: 0 • Changes anytime The filter is used to feedforward the differentiated position command. This parameter is the cut-off frequency of the filter. If position feedforward gain (SEt-34) is 0, this parameter is not valid. In the case of an overshoot, please set the parameter to 0. Please refer to the diagram below for the information about the usage and the setting position of SEt-07. SEt-08 DA Monitor Channel 1 Scale • Setting range: 1 to 65535/V • User Default: 500 • Changes anytime The servo drive can display the analog monitor signals with which the user can check the actual control status through an oscilloscope. Set the scale unit of analog monitor channel 1 at SEt-08. 137
Page 1 and 2:
Maximum Value for OEMs SM CSDP Plus
Page 3 and 4:
Contents 1. Introduction...........
Page 5 and 6:
SEt-32 Brake Inactive Delay Time Af
Page 7 and 8:
A brief introduction to the manual
Page 9 and 10:
1 Introduction Functionality CSDP P
Page 11 and 12:
The models with the same appearance
Page 13 and 14:
The performance specifications of C
Page 15:
Input Voltage B stands for 220V AC.
Page 18 and 19:
Please do not put stress on the ele
Page 20 and 21:
Servo Drive Installation Please che
Page 22 and 23:
Please follow the command below to
Page 24 and 25:
Wiring Specifications Signal line I
Page 26 and 27:
CN1 CN2 Connect the single-phase vo
Page 28 and 29:
Connection with Controller Connect
Page 30 and 31:
32 Higher Control Connector (CN1) C
Page 32 and 33:
Please See "Cable Specifications" i
Page 34 and 35:
Encoder Connector Specifications Mo
Page 36 and 37:
Grounding, Wiring Please separate t
Page 39 and 40:
3 Operation Overview You can instan
Page 41 and 42:
For instance, if you want to set up
Page 43 and 44:
If the revolution speed of the moto
Page 45 and 46:
Monitor Number List No. Contents (U
Page 47 and 48:
Jog Operation The revolution will c
Page 49 and 50:
Current Offset Adjustment To adjust
Page 51 and 52:
Parameter Initialization To return
Page 53 and 54:
SEt-51 Set-up Value Please select t
Page 55 and 56:
4 Control Overview Input signal is
Page 57 and 58:
For instance, put 7 in the fourth d
Page 59 and 60:
Three types of command are inputed
Page 61 and 62:
Please select the position control
Page 63 and 64:
The speed reduction ratio is the ra
Page 65 and 66:
If the distance to move with one pu
Page 67 and 68:
Position Error Range Set the positi
Page 69 and 70:
Speed Command Speed Control Wiring
Page 71 and 72:
If the CN1 connector pins where the
Page 73 and 74:
Torque Control Torque control mode
Page 75 and 76:
If the torque command gain is 100%/
Page 77 and 78:
Multi-level Speed Control Multi-lev
Page 79 and 80:
Multi-level Speed Speed Parameter D
Page 81 and 82:
Combination Control Position contro
Page 83 and 84: 5 Tuning By Gain Adjustment Overvie
Page 85 and 86: If position-related gains alone are
Page 87 and 88: Setting Tuning Coefficient on onlin
Page 89 and 90: Please set torque command filter at
Page 91 and 92: To set up position control-related
Page 93 and 94: P/PI Mode Set-up Function By settin
Page 95 and 96: Set Value 0 Do not use P/PI mode sh
Page 97 and 98: The set-up sequence of the default
Page 99 and 100: 6 Application Motor Stop The servo
Page 101 and 102: When the motor needs to stop during
Page 103 and 104: Please set the brake output waiting
Page 105 and 106: Regenerative Resistor When the oper
Page 107 and 108: This picture shows the case where a
Page 109 and 110: K M ( EL + ER + EC ) EG E = E − +
Page 111 and 112: As shown below, executing command i
Page 113 and 114: Speed Limiting Method Selection Ple
Page 115 and 116: Even when the motor is revolving at
Page 117 and 118: Absolute Encoder An absolute encode
Page 119 and 120: For the controller that can’t rec
Page 121 and 122: 7 Troubleshooting Check Checking Mo
Page 123 and 124: If the voltage of the external batt
Page 125 and 126: The servo drive can notify the cont
Page 127 and 128: If the encoder cable is not connect
Page 129 and 130: If there is an error with the memor
Page 131 and 132: Appendix A Parameter ATTENTION To c
Page 133: SEt-03 Speed Loop Integral Gain •
Page 137 and 138: SEt-11 Reverse Internal Torque Limi
Page 139 and 140: SEt-17 Zero Clamp Level • Setting
Page 141 and 142: SEt-20 Deceleration Time • Settin
Page 143 and 144: SEt-23 Encoder Output Ratio Numerat
Page 145 and 146: SEt-26 Internal Speed Command 1 Int
Page 147 and 148: ATTENTION The brake mounted on the
Page 149 and 150: SEt-33 Following Error Level • Se
Page 151 and 152: SEt-37 Electronic Gear Ratio Denomi
Page 153 and 154: SEt-42 System Gain • Setting rang
Page 155 and 156: SEt-44(1) Dynamic Brake • Setting
Page 157 and 158: SEt-44(4) Encoder Output Pulse Dire
Page 159 and 160: Forward direction is counterclockwi
Page 161 and 162: Open Collector Input SEt-46(4) Spee
Page 163 and 164: When the second digit of SEt-50 is
Page 165 and 166: SEt-53 Motor Capacity • Setting r
Page 167 and 168: SEt-57 Position Error for Speed Int
Page 169 and 170: Put 3 in the second digit of SEt-62
Page 171 and 172: ATTENTION If inertia ratio is set,
Page 173 and 174: SEt-75 Overload Curve Level • Set
Page 175 and 176: SEt-79 Internal Speed Command 4 •
Page 177 and 178: Appendix B Motor Specifications CSM
Page 179 and 180: Speed Torque Curve 181
Page 181 and 182: CSMS Motor Specifications CSMS Moto
Page 183 and 184: Speed Torque Curve 185
Page 185 and 186:
CSMH Motor Specifications CSMH Moto
Page 187 and 188:
189
Page 189 and 190:
Item Specifications Item Specificat
Page 191 and 192:
CSMK Motor Specifications CSMK Moto
Page 193 and 194:
195
Page 195 and 196:
Brake Specifications RSMD Motor Bra
Page 197 and 198:
RSMS Motor Specifications RSMS Moto
Page 199 and 200:
RSMH Motor Specifications RSMH Moto
Page 201 and 202:
203
Page 203 and 204:
Brake Specifications RSMF Motor Bra
Page 205 and 206:
RSMK Motor Specifications RSMK Moto
Page 207 and 208:
209
Page 209 and 210:
Brake Specifications RSML Motor Bra
Page 211 and 212:
RSMN Motor Specifications RSMN Moto
Page 213 and 214:
RSMX Motor Specifications RSMX Moto
Page 215 and 216:
217
Page 217 and 218:
Model LL Brake Present Brake Absent
Page 219 and 220:
RSMD, RSMF, RSMH, RSMK, RSML, RSMS
Page 221 and 222:
Shaft End Size CSM Series Motor Sha
Page 223 and 224:
Appendix C Cable Specifications Mot
Page 225 and 226:
Encoder Cable CSMD, CSMF, CSMH, CSM
Page 227 and 228:
I/O Cable CON-SCONN50PIN cable is u
Page 229 and 230:
Motor Brake Cable CSMD, CSMF, CSMH,
Page 231 and 232:
Appendix D Load Calculation ROLL Lo
Page 233 and 234:
Minimum Acceleration Time (s) Minim
Page 235 and 236:
Load Inertia Moment (kg . m 2 ) Min
Page 237 and 238:
Movement Amount (m) Vl 2t s−ta
Page 239 and 240:
Vertical BALL SCREW Load Mechanical
Page 241 and 242:
Acceleration Torque Required (N . m
Page 243 and 244:
Load Inertia Moment (kg . m 2 ) Min
Page 245 and 246:
Disk Load Mechanical Configuration
Page 247 and 248:
Index Sign /ABS-DT 4-58, 6-121, A-1
Page 249 and 250:
Jog Operation Speed A-146 L Label 1
Page 251 and 252:
Speed Bias Standard Range 5-85, 5-9
Page 254:
CSDP Plus Servo Drive User Manual O
show all

CSDP Plus Servo Drive User Manual

Create successful ePaper yourself

Delete template?

Save as template?