ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 139 ETSI TS 127 007 V11.8.0 (2013-10) +CMOLR= +CMOLR: (list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s),(list of supported s) Description Set command initiates a mobile originated location request (MO-LR). The parameter enables or disables positioning and reporting by unsolicited result codes. Reporting can be performed in the format of GAD shapes or in the format of NMEA strings or both. The unsolicited result codes that can be provided are +CMOLRG: and/or +CMOLRN: . The method to use for positioning is decided by the parameter . The parameters , , , , and indicate accuracy for the MO-LR. The parameter indicates how long the MS will wait for a report before an unsolicited result code is provided. A single report or periodic reports can be requested by the parameter . If periodic reports are requested, the time interval between the reports is specified by the parameter . If GAD shapes are requested, the GAD shapes that will be accepted in the unsolicited result code are defined by the parameter . The parameter specifies the signalling to use for MO-LR. The parameter indicates possible restrictions in supported NMEA strings. The parameter is used to specify the address when reporting to a third party is specified. Additional information about positioning can be found in 3GPP TS 25.305 [77]. If positioning-data cannot be provided at a timeout, the unsolicited result +CMOLRE is provided. Refer subclause 9.2 and subclause 9.3 for possible values. Read command returns the current settings of the parameters , , , , , , , , , , , , and . The parameters , , and are only applicable in certain configurations. The parameter is only applicable if periodic reporting is specified. The parameter is only applicable if reporting is specified by NMEA strings.The parameter is only applicable if reporting to third party is specified. Test command returns the supported values and ranges. Defined values : integer type. Enables and disables reporting location as a result of a MO-LR. Only one can be enabled at any given time. 0 Disables reporting and positioning. 1 Enables reporting of NMEA strings by unsolicited result code +CMOLRN: . Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE. 2 Enables reporting of GAD shapes by unsolicited result code +CMOLRG: . Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE. 3 Enables reporting of NMEA strings and GAD shapes by unsolicited result codes +CMOLRG: and +CMOLRN: . Lack of data at each timeout is indicated by an unsolicited result code +CMOLRE. ETSI
3GPP TS 27.007 version 11.8.0 Release 11 140 ETSI TS 127 007 V11.8.0 (2013-10) NOTE 1: The string of intended for +CMOLR can be split into multiple unsolicited result codes e.g. in order to prevent that the string in the unsolicited result code becomes too long. How to split the string is implementation specific. : integer type. Method for MO-LR. The default value is implementation specific. 0 Unassisted GPS. Autonomous GPS only, no use of assistance data. 1 Assisted GPS (see NOTE 2). 2 Assisted GANSS (see NOTE 2). 3 Assisted GPS and GANSS (see NOTE 2). 4 Basic self location (the network determines the position technology). 5 Transfer to third party. This method makes the parameters and irrelevant (any values are accepted and disregarded). The third party address is given in the parameter (see NOTE 3). 6 Retrieval from third party. This method is to get the position estimate of the third party. The third party address is given in the parameter . NOTE 2: For the methods that require assistance data, the assistance data obtained from the network is used for a UE-based GPS location procedure. NOTE 3: Lack of data at each timeout is not indicated by an unsolicited result code +CMOLRE if reporting to third party is specified. : integer type. 0 Horisontal accuracy not set/specified. 1 Horizontal accuracy set in parameter . : integer type. Requested accuracy as horizontal uncertainty exponent (refer to 3GPP TS 23.032 [76] subclause 6.2). The value range is 0-127. The default value is implementation specific. : integer type. 0 Vertical coordinate (altitude) is not requested, 2D location fix is acceptable. The parameters and do not apply. 1 Vertical coordinate (altitude) is requested, 3D location fix is required. : integer type. 0 Vertical accuracy not set/specified. 1 Vertical accuracy set/specified in parameter . : integer type. Requested accuracy as vertical uncertainty exponent (refer to 3GPP TS 23.032 [76] subclause 6.4). The value range is 0-127. The default value is implementation specific. : integer type. Requested velocity type (refer to 3GPP TS 23.032 [76] subclause 8.6). 0 Velocity not requested. 1 Horizontal velocity requested. 2 Horizontal velocity and vertical velocity requested. 3 Horizontal velocity with uncertainty requested. 4 Horizontal velocity with uncertainty and vertical velocity with uncertainty requested. ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90: 3GPP TS 27.007 version 11.8.0 Relea
Page 139: 3GPP TS 27.007 version 11.8.0 Relea
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

Create successful ePaper yourself

Delete template?

Save as template?