ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 247 ETSI TS 127 007 V11.8.0 (2013-10) 10.1.37 UE's Mobility Management IMS Voice Termination +CMMIVT Table 10.1.QT3-1: +CMMIVT parameter command syntax Command +CMMIVT=[] +CMMIVT +CMMIVT= Possible Response(s) +CMMIVT: +CMMIVT: (list of supported s) Description The set command is used to set the MT to perfom additional procedures as specified in 3GPP TS 24.008 [8] and 3GPP TS 24.301 [83] to support terminating access domain selection by the network. The read command returns the setting, independent of the current serving cell capability and independent of the current serving cell's access technology. Test command returns supported values. Defined Values : integer type; indicates the mobility management IMS voice termination preference of the UE. The default value is manufacturer specific. 1 Mobility Management for IMS Voice Termination disabled 2 Mobility Management for IMS Voice Termination enabled NOTE: The definition of the UE's mobility management IMS voice termination values can be found in 3GPP TS 24.167 [102], subclause 5.31. Implementation Optional. 10.1.38 Power Preference Indication for EPS +CEPPI Table 10.1.38-1: +CEPPI action command syntax Command +CEPPI= +CEPPI= Possible Response(s) +CEPPI: (list of supported s) Description This command indicates whether the MT prefers a configuration primarily optimised for power saving or not. Upon receiving this command, the final result code OK is returned. When in E-UTRAN, if further conditions defined in 3GPP TS 36.331 [86] are met, this can cause transmission of a UEAssistanceInformation message with powerPrefIndication set to to the network. This command may be used in both normal and modem compatibility modes. Defined Values : integer type; indicates the power consumption preference of the MT. 0 normal ETSI
3GPP TS 27.007 version 11.8.0 Release 11 248 ETSI TS 127 007 V11.8.0 (2013-10) 1 low power consumption Implementation Optional. 10.2 Modem compatibility commands 10.2.0 General This subclause describes how existing AT commands, designed for use with a modem, may be used to control a Packet Domain MT. This is to provide backwards compatibility with existing communications software. For new applications it is recommended that the Packet Domain-specific commands, described in previous subclauses, be used. 10.2.1 MT originated PDP context activation 10.2.1.0 General In this mode of operation, the MT behaves like an originating modem and accep<strong>ts</strong> the normal V.250 commands associated with placing and clearing a call. If Packet Domain-specific configuration commands are required, they may be sent to the MT as part of the modem initialization commands. 10.2.1.1 Request packet domain service 'D' Table 130: D command syntax Command D*[*[][*[] [*[[,[,...]]]]]]# Possible Response(s) CONNECT ERROR Description This command causes the MT to perform whatever actions are necessary to establish communication between the TE and the external PDN. The V.250 'D' (Dial) command causes the MT to enter the V.250 online data state and, with the TE, to start the specified layer 2 protocol. The MT shall return CONNECT to confirm acceptance of the command prior to entering the V.250 online data state. No further commands may follow on the AT command line. The detailed behaviour after the online data state has been entered is dependent on the PDP type. It is described briefly in clause 9 (for IP) of 3GPP TS 27.060 [34]. PS attachment and PDP context activation procedures may take place prior to or during the PDP startup if they have not already been performed using the +CGATT and +CGACT commands. When the layer 2 protocol has terminated, either as a result of an orderly shut down of the PDP or an error, the MT shall enter V.250 command state and return the NO CARRIER final result code. If is supported and provided, the MT shall automatically set up a virtual call to the specified address after the PDP context has been activated. If and are supported, their usage shall be the same as in the +CGDATA command. The +CGDCONT, +CGQREQ, etc. commands may be used in the modem initialization AT command string to set values for for PDP type, APN, QoS etc.. If is not supported or is supported but omitted, the MT shall use a layer 2 protocol appropriate to the PDP type. If is not supported or is supported but omitted, the MT shall attempt to activate the context using: (a) any information provided by the TE during the PDP startup procedure, e.g. the TE may provide a PDP type and/or PDP address to the MT; ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198: 3GPP TS 27.007 version 11.8.0 Relea
Page 247: 3GPP TS 27.007 version 11.8.0 Relea
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?