ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 221 ETSI TS 127 007 V11.8.0 (2013-10) The PDP addresses are considered to match if they are identical or if either or both addresses are unspecified. For example, a PPP NCP request specifying PDP type = IP and no PDP address would cause the MT to search through the specified context definitions for one with PDP type = IP and any PDP address. The context shall be activated using the matched value for PDP type and a static PDP address if available, together with the other information found in the PDP context definition. If a static PDP address is not available then a dynamic address is requested. If no is given or if there is no matching context definition, the MT shall attempt to activate the context with whatever information is available to the MT. The other context parameters shall be set to their default values. If the activation is successful, data transfer may proceed. After data transfer is complete, and the layer 2 protocol termination procedure has completed successfully, the V.250 command state is re-entered and the MT returns the final result code OK. In the event of an erroneous termination or a failure to start up, the V.250 command state is re-entered and the MT returns the final result code NO CARRIER or, if enabled, +CME ERROR. Refer subclause 9.2 for possible values. Attach, activate and other errors may be reported. The test command is used for requesting information on the supported layer 2 protocols. This command may be used in both normal and modem compatibility modes. Defined Values : string type; indicates the layer 2 protocol to be used between the TE and MT NULL PPP PAD X25 M-xxxx none, for PDP type OSP:IHOSS (Obsolete) Point-to-point protocol for a PDP such as IP character stream for X.25 character (triple X PAD) mode (Obsolete) X.25 L2 (LAPB) for X.25 packet mode (Obsolete) manufacturer-specific protocol (xxxx is an alphanumeric string) If the value is omitted, the layer 2 protocol is unspecified. Other values are reserved and will result in an ERROR response. : integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT commands). Implementation Optional if the D (dial) command can be used to specify Packet Domain operation. ETSI
3GPP TS 27.007 version 11.8.0 Release 11 222 ETSI TS 127 007 V11.8.0 (2013-10) 10.1.13 Configure local octet stream PAD parameters +CGCLOSP (Obsolete) 10.1.14 Show PDP address(es) +CGPADDR Table 123: +CGPADDR action command syntax Command +CGPADDR[=[, [,...]]] Possible response(s) [+CGPADDR: [,[,]]] [+CGPADDR: ,[[ ,]] [...]] +CGPADDR= +CGPADDR: (list of defined s) NOTE: The syntax of the AT Set Command is corrected to be according to ITU-T Recommendation V.250 [14]. Older versions of the specification specify incorrect syntax +CGPADDR=[,[,[,...]]]. Description The execution command returns a list of PDP addresses for the specified context identifiers. If no is specified, the addresses for all defined contex<strong>ts</strong> are returned. The test command returns a list of defined s. Defined values : integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT commands). and : each is a string type that identifies the MT in the address space applicable to the PDP. The address may be static or dynamic. For a static address, it will be the one set by the +CGDCONT and +CGDSCONT commands when the context was defined. For a dynamic address it will be the one assigned during the last PDP context activation that used the context definition referred to by . Both and are omitted if none is available. Both and are included when both IPv4 and IPv6 addresses are assigned, with containing the IPv4 address and containing the IPv6 address. The string is given as dot-separated numeric (0-255) parameter of the form: a1.a2.a3.a4 for IPv4 and a1.a2.a3.a4.a5.a6.a7.a8.a9.a10.a11.a12.a13.a14.a15.a16 for IPv6. When +CGPIAF is supported, i<strong>ts</strong> settings can influence the format of the IPv6 address in parameter or returned with the execute form of +CGPADDR. NOTE: In dual-stack terminals ( IPV4V6), the IPv6 address will be provided in . For terminals with a single IPv6 stack ( IPV6) or due to backwards compatibility, the IPv6 address can be provided in parameter . Implementation Optional. ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172: 3GPP TS 27.007 version 11.8.0 Relea
Page 221: 3GPP TS 27.007 version 11.8.0 Relea
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?