ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 201 ETSI TS 127 007 V11.8.0 (2013-10) If the initial PDP context is supported, the context with =0 is automatically defined at startup, see subclause 10.1.0. As all other contexts, the parameters for =0 can be modified with +CGDCONT. If the initial PDP context is supported, +CGDCONT=0 resets context number 0 to its particular default settings. The read command returns the current settings for each defined context. The test command returns values supported as a compound value. If the MT supports several PDP types, , the parameter value ranges for each are returned on a separate line. Defined values : integer type; specifies a particular PDP context definition. The parameter is local to the TE-MT interface and is used in other PDP context-related commands. The range of permitted values (minimum value = 1 or if the initial PDP context is supported (see subclause 10.1.0), minimum value = 0) is returned by the test form of the command. NOTE 1: The s for network-initiated PDP contexts will have values outside the ranges indicated for the in the test form of the commands +CGDCONT and +CGDSCONT. : string type; specifies the type of packet data protocol X.25 ITU-T/CCITT X.25 layer 3 (Obsolete) IP Internet Protocol (IETF STD 5 [103]) IPV6 Internet Protocol, version 6 (see RFC 2460 [106]) IPV4V6 OSPIH Virtual introduced to handle dual IP stack UE capability. (See 3GPP TS 24.301 [83]) Internet Hosted Octect Stream Protocol (Obsolete) PPP Point to Point Protocol (IETF STD 51 [104]) NOTE 2: Only IP, IPV6 and IPV4V6 values are supported for EPS services. : string type; a logical name that is used to select the GGSN or the external packet data network. If the value is null or omitted, then the subscription value will be requested. : string type; identifies the MT in the address space applicable to the PDP. If the parameter value is null or omitted, then a value may be provided by the TE during the PDP startup procedure or, failing that, a dynamic address will be requested. The read form of the command will continue to return the null string even if an address has been allocated during the PDP startup procedure. The allocated address(es) may be read using the +CGPADDR command. When +CGPIAF is supported, its settings can influence the format of this parameter returned with the read form of +CGDCONT. NOTE 3: For EPS, this field or the parameter value of the field is omitted. : integer type; controls PDP data compression (applicable for SNDCP only) (refer 3GPP TS 44.065 [61]) 0 off 1 on (manufacturer preferred compression) 2 V.42bis 3 V.44 : integer type; controls PDP header compression (refer 3GPP TS 44.065 [61] and 3GPP TS 25.323 [62]) ETSI
3GPP TS 27.007 version 11.8.0 Release 11 202 ETSI TS 127 007 V11.8.0 (2013-10) 0 off 1 on (manufacturer preferred compression) 2 RFC 1144 [105] (applicable for SNDCP only) 3 RFC 2507 [107] 4 RFC 3095 [108] (applicable for PDCP only) : integer type; controls how the MT/TA requests to get the IPv4 address information 0 IPv4 Address Allocation through NAS Signalling 1 IPv4 Address Allocated through DHCP : integer type; indicates whether the PDP context is for emergency bearer services or not. 0 PDP context is not for emergency bearer services 1 PDP context is for emergency bearer services : integer type; influences how the MT/TA requests to get the P-CSCF address, see 3GPP TS 24.229 [89] annex B and annex L. 0 Preference of P-CSCF address discovery not influenced by +CGDCONT 1 Preference of P-CSCF address discovery through NAS Signalling 2 Preference of P-CSCF address discovery through DHCP : integer type; indicates to the network whether the PDP context is for IM CN subsystem-related signalling only or not. 0 UE indicates that the PDP context is not for IM CN subsystem-related signalling only 1 UE indicates that the PDP context is for IM CN subsystem-related signalling only Implementation Mandatory unless only a single subscribed context is supported. 10.1.2 Define secondary PDP context +CGDSCONT Table 112: +CGDSCONT parameter command syntax Command Possible response(s) +CGDSCONT=[,[,[,[,]]]] +CGDSCONT [+CGDSCONT: ,,,,] [+CGDSCONT: ,,,, +CGDSCONT= [...]] +CGDSCONT: (range of supported s),(list of s for active primary contexts),(list of supported s),(list of supported s),(list of supported s) ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152: 3GPP TS 27.007 version 11.8.0 Relea
Page 201: 3GPP TS 27.007 version 11.8.0 Relea
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?