ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 241 ETSI TS 127 007 V11.8.0 (2013-10) Description The set command is used to set the MT to operate according to the specified mode of operation for EPS, see 3GPP TS 24.301 [83]. If the requested mode of operation is not supported, an ERROR or +CME ERROR response is returned. Extended error responses are enabled by the +CMEE command. Refer subclause 9.2 for possible values. The read command returns the mode of operation set by the TE, independent of the current serving cell capability and independent of the current serving cell Access Technology. The test command is used for requesting information on the supported MT mode of operation. Defined Values : integer type; indicates the mode of operation 0 PS mode 2 of operation 1 CS/PS mode 1 of operation 2 CS/PS mode 2 of operation 3 PS mode 1 of operation NOTE: the definition for UE modes of operation can be found in 3GPP TS 24.301 [83] Implementation Optional. 10.1.29 Delete non-active PDP contexts +CGDEL Table 10.1.29-1: +CGDEL action command syntax Command +CGDEL[=] Possible Response(s) [+CGDEL: [,[,...]]] +CME ERROR: +CGDEL= Description The execution command +CGDEL= removes the indicated PDP context and removes all associated data related to the indicated PDP contexts that are not activated. The AT command will not delete or remove information for activated PDP contexts. The removed PDP context is listed by the +CGDEL: intermediate result code. If the initial PDP context is supported (see subclause 10.1.0), +CGDEL=0 will return ERROR and the context will not be removed. If points to a primary PDP context, the PDP context will be deleted together with all linked secondary PDP contexts if none of the PDP contexts are activated. If points to a secondary PDP context, the PDP context will be deleted if it is not activated. A special form of the command can be given as +CGDEL (with the = omitted). In this form, all primary PDP contexts that are not activated or have any activated secondary PDP contexts will be removed and all secondary PDP contexts that are not activated will be removed. The associated data of all the deleted PDP contexts will be removed, and the removed PDP context are listed by the +CGDEL: [,[,...]] intermediate result code. Activated PDP contexts will not cause this form of the command to return ERROR or +CME ERROR. Refer subclause 9.2 for possible values. If the initial PDP context is supported (see subclause 10.1.0), +CGDEL (with the = omitted) will not cause the initial PDP context to be removed or cause +CGDEL to return ERROR. ETSI
3GPP TS 27.007 version 11.8.0 Release 11 242 ETSI TS 127 007 V11.8.0 (2013-10) NOTE: +CGDEL will remove associated PDP context data that can be set by the AT commands +CGDCONT, +CGDSCONT, +CGTFT, +CGEQREQ, +CGEQMIN and +CGEQOS. For an attempt to delete PDP context(s) which would violate these rules, a +CME ERROR response is returned. Refer subclause 9.2 for possible values. Defined values : integer type; specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT commands). Implementation Optional. 10.1.30 Signalling connection status +CSCON Table 10.1.30-1: +CSCON parameter command syntax Command +CSCON=[] +CSCON +CSCON= Possible response(s) +CME ERROR: +CSCON: ,[,] +CME ERROR: +CSCON: (list of supported s) Description The set command controls the presentation of an unsolicited result code +CSCON. If =1, +CSCON: is sent from the MT when the connection mode of the MT is changed. If =2 and there is a state within the current mode, +CSCON: [,] is sent from the MT. If setting fails, an MT error, +CME ERROR: is returned. Refer subclause 9.2 for possible values. When the MT is in UTRAN or E-UTRAN, the mode of the MT refers to idle when no PS signalling connection and to connected mode when a PS signalling connection between UE and network is setup. When the UE is in GERAN, the mode refers to idle when the MT is in either the IDLE state or the STANDBY state and to connected mode when the MT is in READY state. The value indicates the state of the MT when the MT is in UTRAN connected mode. The read command returns the status of result code presentation and an integer which shows whether the MT is currently in idle mode or connected mode. State information is returned only when =2. Test command returns supported values as compound value. Defined values : integer type 0 disable unsolicited result code 1 enable unsolicited result code +CSCON: 2 enable unsolicited result code +CSCON: [,] : integer type; indicates the signalling connection status 0 idle 1 connected ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192: 3GPP TS 27.007 version 11.8.0 Relea
Page 241: 3GPP TS 27.007 version 11.8.0 Relea
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?