ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 41 ETSI TS 127 007 V11.8.0 (2013-10) Defined values : integer type; multislot class : integer type; maximum number of receive timeslots that MT can use : integer type; maximum number of transmit timeslots that MT can use : integer type; total number of receive and transmit timeslots that MT can use at the same time (per TDMA frame). The following applies in a HSCSD call: 1 ≤ (receive slots) + (transmit slots) ≤ is a sum of integers each representing a supported channel coding (e.g. value 5 indicates that 4,8k and 9,6k channel codings are supported): 1 4,8k full rate data traffic channel 4 9,6k full rate data traffic channel 8 14,4k full rate data traffic channel 16 28,8k full rate data traffic channel (only possible when 14.4k is supported) 32 32,0k full rate data traffic channel (only possible in a two-timeslot configuration) 64 43,2k full rate data traffic channel (only possible when 14.4k is supported) Implementation Mandatory when HSCSD implemented. This command is not applicable to UTRAN or E-UTRAN UEs. 6.13 HSCSD transparent call configuration +CHST Table 20: +CHST parameter command syntax Command +CHST=[[,]] +CHST +CHST= Possible response(s) +CHST: , Description Set command controls parameters for transparent HSCSD calls in GERAN. Changing them during a call does not affect the current call. NOTE: In UTRAN or E-UTRAN, values set with this command are not needed. The only applicable parameter is , which is set with +CBST command. Defined values : integer type; wanted amount of receive timeslots. Default value 0 indicates that TA shall calculate a proper value from currently selected fixed network user rate ( subparameter from +CBST command) and : a sum of integers each representing a channel coding that is accepted for transparent HSCSD calls. Default value 0 indicates that all supported codings are accepted (refer +CHSD command for other values) Implementation Mandatory when transparent HSCSD implemented. This command is not applicable to UTRAN or E-UTRAN UEs. ETSI
3GPP TS 27.007 version 11.8.0 Release 11 42 ETSI TS 127 007 V11.8.0 (2013-10) 6.14 HSCSD non-transparent call configuration +CHSN Table 21: +CHSN parameter command syntax Command +CHSN=[[,[, [,]]]] +CHSN +CHSN= Possible response(s) +CHSN: ,,, +CHSN: (list of supported s),(list of supported s),(list of supported s),(list of supported s) Description Set command controls parameters for originating non-transparent HSCSD calls. Values may also be used during mobile terminated data call setup. In GERAN, changing or value during a call does not affect the current call. In GERAN, changing of or affects the current call only if was non-zero when call was established. Defined values : integer type; wanted air interface user rate. Default value 0 indicates that TA shall calculate a proper value from currently selected fixed network user rate ( subparameter from +CBST command), , and (or from +CHSD command if =0). Other values: 1 9600 bps 2 14400 bps 3 19200 bps 4 28800 bps 5 38400 bps 6 43200 bps 7 57600 bps : integer type; wanted amount of receive timeslots. Default value 0 indicates that TA shall calculate a proper value from currently selected and . This parameter is not applicable to UTRAN or E- UTRAN UEs. : integer type; top value for that user is going to request during the next established nontransparent HSCSD call. Default value 0 indicates that user is not going to change / during the next call. This parameter is not applicable to UTRAN or E-UTRAN UEs. : a sum of integers each representing a channel coding that is accepted for non-transparent HSCSD calls. Default value 0 indicates that all supported codings are accepted (refer +CHSD command for other values). This parameter is not applicable to UTRAN or E-UTRAN UEs. Implementation Mandatory when non-transparent HSCSD implemented. 6.15 HSCSD current call parameters +CHSC Table 22: +CHSC action command syntax Command +CHSC Possible response(s) +CHSC: ,,, ETSI
Page 1 and 2: ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4: 3GPP TS 27.007 version 11.8.0 Relea
Page 41: 3GPP TS 27.007 version 11.8.0 Relea
Page 93 and 94:
3GPP TS 27.007 version 11.8.0 Relea
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

Create successful ePaper yourself

Delete template?

Save as template?