ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 273 ETSI TS 127 007 V11.8.0 (2013-10) Optional. 13.2.3 Hangup of current calls +CHCCS Table 13.2.3-1: +CHCCS action command syntax Command +CHCCS=[,] Possible response(s) +CME ERROR: when =value>0 is inserted and command successful: [+CHCCSI: ] when =0 is inserted and command successful: +CHCS= [+CHCCSI: [+CHCCSI: ] [...]] Description Execution command causes the TA to initiate hangup and subsequently perform call clearing of the call for which a was provided when the call was detected in the MT. The parameter can be added to indicate particular information on the cause for call clearing. Setting the parameter to values 2 or 3 is typically relevant for call clearing before a call has been established (e.g. an incoming or waiting call). The parameter is ignored by the lower layers if it is not according to the signalling procedures in question. A special form of the execution command, +CHCCS=0, causes the TA to initiate hangup and subsequently perform call clearing of all calls for which a was provided when the call was detected in the MT. The parameter will be ignored if =0. The information text +CHCCSI: is provided for each call where a successful hangup is initiated as result of the +CHCCS. If no hangup is initiated, no information text is provided before OK is returned. NOTE 1: The command +CHCCS=0 will initiate hangup of all calls with a . This also applies to calls on hold and call waiting calls. Refer subclause 9.2 for possible values. Defined values : integer type. Call identification number as described in 3GPP TS 22.030 [19] subclause 6.5.5.1. This number can be used in +CHLD command operations. Value range is from 1 to N. N, the maximum number of simultaneous call control processes is implementation specific. NOTE 2: When +CMCCS is supported, the call identification number is not reset until the unsolicited result code +CMCCSI has indicated that the =1 (Idle). : integer type. Proposed cause value for call clearing. 0 No particular cause indicated 1 Cause "Normal call clearing" (value 16), see 3GPP TS 24.008 [8] table 10.5.123 or BYE request, see RFC 3261 [111] subclause 15.1 2 Cause "Call rejected" (value 21), see 3GPP TS 24.008 [8] table 10.5.123 or "488 Not Acceptable Here", see RFC 3261 [111] subclause 21.4.26 ETSI
3GPP TS 27.007 version 11.8.0 Release 11 274 ETSI TS 127 007 V11.8.0 (2013-10) 3 Cause "User busy" (value 17), see 3GPP TS 24.008 [8] table 10.5.123 or "486 Busy Here", see RFC 3261 [111] subclause 21.4.24 Implementation Mandatory when +CDU is implemented in the TA. 13.2.4 Define media profile +CDEFMP Table 13.2.4-1: +CDEFMP parameter command syntax Command Possible response(s) +CDEFMP=[][,] +CME ERROR: When no but provided and command successful: [+CDEFMP: ] +CDEFMP [+CDEFMP: , [+CDEFMP: , +CDEFMP= [...]]] +CDEFMP: (range of supported s) Description A media profile is identified by i<strong>ts</strong> media profile identification number. A media profile defines an SDP media description to be used in SDP offers and SDP answers. Media profiles can be used with +CDU and +CDUP when dialling URIs. The set command specifies the SDP media description for a media profile identified by the (local) media profile identification number, . When no value is provided then a new SDP media description is defined and the media profile"s identification number is returned by the command"s response. When an value is provided, the definition of the SDP media description identified by the media profile identification number is replaced with the SDP media description provided by the command. A special form of the set command, +CDEFMP= causes the SDP media description for the indicated media profile to become undefined. Further, +CDEFMP= causes the SDP media description for all defined media profiles to become undefined. The read command returns a list of all defined media profiles. The test command returns values supported as a compound value. Refer subclause 9.2 for possible values. Defined values : integer type. Media profile identification number. The parameter is local to the TE-MT interface. The range of permitted values (minimum value = 1) is returned by the test form of the command. The MT shall use the indicated SDP media description for the in the initial SDP offer for a call setup. : string type represented with IRA characters. SDP media description including media level SDP lines. This parameter shall not be subject to conventional character conversion as per +CSCS. This parameter can contain the following types of SDP lines: SDP m-lines, SDP a-lines and partial SDP m-lines. ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224: 3GPP TS 27.007 version 11.8.0 Relea
Page 273: 3GPP TS 27.007 version 11.8.0 Relea
show all

ts_127007v110800p

Create successful ePaper yourself

Delete template?

Save as template?