ts_127007v110800p

Recommendations

Info

3GPP TS 27.007 version 11.8.0 Release 11 243 ETSI TS 127 007 V11.8.0 (2013-10) : integer type; indicates the RRC state information if the MT is in connected Mode while in UTRAN. 0 UTRAN URA_PCH state 1 UTRAN Cell_PCH state 2 UTRAN Cell_FACH state 3 UTRAN Cell_DCH state Implementation Optional. 10.1.31 Define PDP context authentication parameters +CGAUTH Table 10.1.31-1: +CGAUTH parameter command syntax Command Possible response(s) +CGAUTH=[,[, +CME ERROR: [,]]] +CGAUTH [+CGAUTH: ,,,] [+CGAUTH: ,,, [...]] +CGAUTH= +CGAUTH: (range of supported s),(list of supported s),(range of supported s),(range of supported s) Description Set command allows the TE to specify authentication parameters for a PDP context identified by the (local) context identification parameter used during the PDP context activation and the PDP context modification procedures. Since the is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, +CGAUTH is effectively as an extension to these commands. Refer subclause 9.2 for possible values. The read command returns the current settings for each defined context. The test command returns values supported as a compound value. Defined values : integer type. Specifies a particular PDP context definition (see the +CGDCONT and +CGDSCONT commands). : integer type. Authentication protocol used for this PDP context. 0 None. Used to indicate that no authentication protocol is used for this PDP context. Username and password are removed if previously specified. 1 PAP 2 CHAP : String type. User name for access to the IP network. : String type. Password for access to the IP network. Implementation Optional. ETSI
3GPP TS 27.007 version 11.8.0 Release 11 244 ETSI TS 127 007 V11.8.0 (2013-10) 10.1.32 Initial PDP context activation +CIPCA Table 10.1.32-1: +CIPCA parameter command syntax Command +CIPCA=[] +CIPCA +CIPCA= +CIPCA: Possible response(s) +CIPCA: (list of supported s) Description The set command controls whether an initial PDP context (see subclause 10.1.0) shall be established automatically following an attach procedure when the UE is attached to GERAN or UTRAN RATs. For ≠0, deactivating the last (active) PDP context can lead to a (re)establishment of the initial PDP context. Changing setting of from 0 to 1 will cause an immediate attempt to (re)establish the initial PDP context if no PDP context is active. Changing from 0 to 2 will if not roaming cause an immediate attempt to (re)establish the initial PDP context if no other PDP context is active. Changing will never cause a PDP context deactivation. NOTE 1: This command does not affect connectivity behavior in E-UTRAN, which mandates the UE to establish a PDP context upon attach. NOTE 2: For this command, the term roaming corresponds to being registered to a VPLMN which is not equivalent to HPLMN or EHPLMN. The read command returns the current setting of the command. The test command returns values supported as a compound value. Defined values : integer type. Activation of PDP context upon attach. 0 Do not activate 1 Always activate 2 Activate when not roaming Implementation Optional. 10.1.33 No more PS data +CNMPSD Table 10.1.33-1: +CNMPSD action command syntax +CNMPSD +CNMPSD= Command Possible Response(s) Description This command indicates that no application on the MT is expected to exchange data. Upon receiving this command, the final result code OK is returned. When in UTRAN, if further conditions defined in 3GPP TS 25.331 [74] are met, this can cause transmission of a SIGNALLING CONNECTION RELEASE INDICATION message with the cause "UE Requested PS Data session end". ETSI
Page 1 and 2:
ETSI TS 127 007 V11.8.0 (2013-10) T
Page 3 and 4:
3GPP TS 27.007 version 11.8.0 Relea
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194: 3GPP TS 27.007 version 11.8.0 Relea
Page 243: 3GPP TS 27.007 version 11.8.0 Relea
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

ts_127007v110800p

Create successful ePaper yourself

Delete template?

Save as template?