Series 04 Ku-Band TVRO Antenna

More documents

Recommendations

Info

Setup Series 04 Ku-Band TVRO Antenna This Page Intentionally Left Blank 5-4
Series 04 Ku-Band TVRO Antenna Functional Testing 6. Functional Testing If not already ON, Turn ON the Power switch on the front panel of the ACU. 6.1. (OPTIONAL) TSC-10 Touch Screen Controller Checks Refer to the functional testing chapter of the TSC-10 manual for check to perform. 6.2. ACU / Antenna System Check 1. Press RESET on the ACU front panel to initialize the system. Verify the display shows "SEA TEL INC - MASTER" and the ACU software version number. Wait 10 seconds for the display to change to "SEA TEL INC - REMOTE" and the PCU software version number. If the display shows "REMOTE INITIALIZING”, wait approximately 2 minutes for the antenna to complete initialization and report the Antenna Model and PCU software version. If “REMOTE NOT RESPONDING" is displayed, refer to the Troubleshooting Section of this manual. 2. Press the NEXT key repeatedly to display the Ship, Satellite, Antenna and Status menu displays. This verifies that the displays change in the correct response to the keys. 6.3. Latitude/Longitude Auto-Update check This verifies that the GPS antenna mounted on the antenna pedestal is automatically updating the current ship’s position information. If the GPS is not updating the ACU properly, refer to the Troubleshooting Section of this manual. 1. Press the NEXT key repeatedly to display the Ship menu. Press ENTER to access edit mode and view the current Latitude value. 2. Press the LEFT arrow key to bring the cursor up under the ones digit, press UP and then hit ENTER. The display should immediately show a latitude value one degree higher. If the GPS engine mounted on the Antenna Pedestal is working properly the incorrect value will be overwritten within several seconds (back to the correct current value). 3. This test does not need to be repeated in the Longitude menu. 6.4. Azimuth & Elevation Drive This check verifies that the antenna moves in the correct direction in response to the keys. If the antenna is not driving properly, refer to the Troubleshooting Section of this manual. 1. Press the NEXT key several times to display the Antenna menu. 2. Press the Tracking key to toggle Tracking OFF. 3. Press the UP arrow key repeatedly and verify that the antenna moves up in elevation. 4. Press the DOWN arrow key repeatedly and verify that the antenna moves down in elevation. 5. Press the RIGHT arrow key repeatedly and verify that the antenna moves up in azimuth. 6. Press the LEFT arrow key repeatedly and verify that the antenna moves down in azimuth. 6-1
Page 1 and 2: INSTALLATION AND OPERATION MANUAL F
Page 4 and 5: Revision History REV ECO# Date Desc
Page 6 and 7: Table of Contents Series 04 Ku-Band
Page 8 and 9: Table of Contents Series 04 Ku-Band
Page 10 and 11: Introduction Series 04 Ku-Band TVRO
Page 12 and 13: Operation Series 04 Ku-Band TVRO An
Page 14 and 15: Basic System Information Series 04
Page 22 and 23: Installation Series 04 Ku-Band TVRO
Page 24 and 25: Installation Series 04 Ku-Band TVRO
Page 26 and 27: Setup Series 04 Ku-Band TVRO Antenn
Page 30 and 31: Functional Testing Series 04 Ku-Ban
Page 32 and 33: Troubleshooting and Maintenance Ser
Page 78 and 79:
Troubleshooting and Maintenance Ser
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Specifications Series 04 Ku-Band TV
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Drawings Series 04 Ku-Band TVRO Ant
Page 94:
SINGLE LEVEL MFG BILL OF MATERIAL F
Page 97 and 98:
8 7 6 5 4 3 2 1 NOTES: (UNLESS OTHE
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 107 and 108:
NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 112:
Page 118 and 119:
Page 120:
show all

Series 04 Ku-Band TVRO Antenna

Create successful ePaper yourself

Delete template?

Save as template?