Series 04 Ku-Band TVRO Antenna

More documents

Recommendations

Info

Troubleshooting and Maintenance Series 04 Ku-Band TVRO Antenna 10. Using 3/8” Nut Driver, remove the three 10/32 Hex Nuts and #10 Flat Washers and then remove the Polang Relay Assembly. 11. Replace the Polang Relay Assembly and secure with Loctite 222 and the hardware removed in step 10. 12. Re-Install connections removed in steps 9, 8 and 7. 13. Re-Install right El pan and secure using Loctite 222 and hardware removed in steps 1 through 6. 14. Check and/or adjust Antenna balance. 7.4.13. Replacing 24VDC Polang Motor Assembly Series 04 Polang Motor replacement procedure is as follows. Tools Required: • ¼” and 7/16” Open Ended Wrench • 5/64”, 7/64”, and 5/32” Allen Wrench’s • Snips/ Cutters • Loctite 222 or equiv. NOTE: Unless otherwise indicated, all nuts and bolts should be assembled with Loctite 222 or its equivalent. 7-40
Series 04 Ku-Band TVRO Antenna Troubleshooting and Maintenance 1. Using a ¼” Wrench, remove the four 4-40 Small Pattern Hex Nuts and Washers. Remove Vertex Feed Tube and set aside. Save all Hardware for future use. 2. Using the 7/16” Wrench, remove the RF Cables connecting to LNB. 3. Using snips, cut tie wrap(s) securing harness to LNB if needed. 4. Using the 7/64” Allen Head remove Polang Harness ground Lug attached to Polang plate. 5. Unplug Polang Harness IDC connection. 6. Using a 5/64” Allen Wrench, loosen the three setscrews in LNB Mounting Cuff and remove LNB from feed assembly. (Photo shown without LNB installed for setscrew location clarity). 7. Using snips, cut tie wraps securing harness to Polang Motor assembly. 7-41
Page 1 and 2:
INSTALLATION AND OPERATION MANUAL F
Page 4 and 5:
Revision History REV ECO# Date Desc
Page 6 and 7:
Table of Contents Series 04 Ku-Band
Page 8 and 9:
Table of Contents Series 04 Ku-Band
Page 10 and 11:
Introduction Series 04 Ku-Band TVRO
Page 12 and 13:
Operation Series 04 Ku-Band TVRO An
Page 14 and 15:
Basic System Information Series 04
Page 16 and 17:
Page 18 and 19:
Page 20 and 21: Basic System Information Series 04
Page 22 and 23: Installation Series 04 Ku-Band TVRO
Page 24 and 25: Installation Series 04 Ku-Band TVRO
Page 26 and 27: Setup Series 04 Ku-Band TVRO Antenn
Page 28 and 29: Setup Series 04 Ku-Band TVRO Antenn
Page 30 and 31: Functional Testing Series 04 Ku-Ban
Page 32 and 33: Troubleshooting and Maintenance Ser
Page 86 and 87: Specifications Series 04 Ku-Band TV
Page 92 and 93: Drawings Series 04 Ku-Band TVRO Ant
Page 94: SINGLE LEVEL MFG BILL OF MATERIAL F
Page 97 and 98: 8 7 6 5 4 3 2 1 NOTES: (UNLESS OTHE
Page 105 and 106: NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 107 and 108: NOTES: (UNLESS OTHERWISE SPECIFIED)
Page 112: SINGLE LEVEL MFG BILL OF MATERIAL F
Page 118 and 119: SINGLE LEVEL MFG BILL OF MATERIAL F
Page 120:
SINGLE LEVEL MFG BILL OF MATERIAL F
show all

Series 04 Ku-Band TVRO Antenna

Create successful ePaper yourself

Delete template?

Save as template?