User's Manual - Pixord

More documents

Recommendations

Info

connector) at the same time and get the correct video quality, you mustswitch the corresponding 75Ω switch to “off” position.‣ Ensure you power supply adapter specification (Input AC 110V or 220V,Output AC 9V 1A) matches to your power line, and connect the powersupply to the Network Video Server.‣ Check the power LED (red) is constant lit, and the network LED (display linkstatus) should light up (red) less than 10 seconds if your networkconnection is correct.12 / 88
3.3 Network Camera Installation Procedure3.3.1 Mount the PiXORD Network CameraThe PiXORD NC provides screw holes on both the top and bottom surfaces of theunit for mounting the stand assembly. You can mount your PiXORD NC on adesktop, a wall, or ceiling by adjusting the linked way of stand assembly.3.3.2 Connect to NetworkConnect an Ethernet cable (twisted pair CAT5 terminated cable with a standardRJ-45 connector) to your PiXORD NC and attach it to the network.13 / 88
Page 1 and 2: PiXORD241/240/200/205/120/100/126/1
Page 3 and 4: 5.1.1 Configurations Overview......
Page 5 and 6: 1 Introduction1.1 What is PiXORD Ne
Page 7 and 8: 2 Physical Connections2.1 Front Pan
Page 9 and 10: 2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11: 3 Installation3.1 System Requiremen
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64:
‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66:
‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68:
6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70:
‣ Weight0.93 kg, excluding power
Page 71 and 72:
‣ Operating Temperature5 °C~50°
Page 73 and 74:
- Video throughput: Up to 30 frames
Page 75 and 76:
‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78:
6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80:
- DirectX 9.0c‣ Security- Three-l
Page 81 and 82:
FTP image to remote site;E-mail ima
Page 83 and 84:
- One RS-232 serial port for extern
Page 85 and 86:
2x LEDs to indicate network and pow
Page 87 and 88:
6. HTTP server push to remote site
show all

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?