User's Manual - Pixord

More documents

Recommendations

Info

‣ Already registered: Another user had registered this name; please changeyour register name by changing "server name" in chapter 5.1.1 ServerGeneral Settings .Example: To setup a PiXORD200 (IP address 192.168.0.200) behind a dialup ADSLrouter, and wish to access by name http://demo.ddns.pixord.com/. And, theprocedure is as below:‣ Configure the ADSL router with PPPoE enable; Lan IP, 192.168.0.254; andsubnet mask, 255.255.255.0.‣ Assign the ADSL router's virtual server with service port 80 to server IP192.168.0.200‣ Configure PiXORD200 network configuration with IP address 192.168.0.200;subnet 255.255.255.0; DNS1 with valid DNS address such as 168.95.192.1 or168.95.1.1; gateway IP address with 192.168.0.254 (router's IP); HTTP portwith port 80.‣ Configure server name in chapter 5.1.1 Server General Settings with"demo".‣ Configure DDNS with Activate; Address "ddns.pixord.com"; DDNS with port80; Router Incoming port 80; and update time with 600 (10 minutes). Finally,clicks submit.‣ If DDNS message success, then enter URL http://demo.ddns.pixord.com/ onbrowser. Consequentially, it will show PiXORD NVS's home page.Click "Save Changes" bottom if needed for existing data changed in PiXORD NVSwhen power off.38 / 88
5.4 I/O Configuration5.4.1 Serial Port ManagementChange the serial port mode and configure the serial port settings. Refer toAppendix E -I/O & COM port Connectors for details.5.4.2 PTZ Adjustment39 / 88
Page 1 and 2: PiXORD241/240/200/205/120/100/126/1
Page 3 and 4: 5.1.1 Configurations Overview......
Page 5 and 6: 1 Introduction1.1 What is PiXORD Ne
Page 7 and 8: 2 Physical Connections2.1 Front Pan
Page 9 and 10: 2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12: 3 Installation3.1 System Requiremen
Page 13 and 14: 3.3 Network Camera Installation Pro
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37: ‣ Dynamic DNS Activate: Click on
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64: ‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70: ‣ Weight0.93 kg, excluding power
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78: 6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80: - DirectX 9.0c‣ Security- Three-l
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?