User's Manual - Pixord

More documents

Recommendations

Info

conflicts may endanger the Flash devices.‣ Start the FTP session and log in to the PiXORD NVSFor example, in our case for Windows98:Enter DOS by "start->Program->MS-DOS Prompt"Change to the directory where the latest flash.bin exist.Start ftp session by enter "ftp Enter "root" as USERNAME, "pass" as PASSWORD if no user in UserList record. In case any user list exists, you will have to use youradministrator's USERNAME and PASSWORD to login‣ Set FTP to binary mode using the command "bin".In FTP session window, Enter "bin"‣ Upload the software into PiXORD NVS by FTP "put" command.In FTP session window, enter "put flash.bin"In FTP session window, enter "bye" to quit FTP session.‣ FTP session may freeze for around 1 minute to transfer and automaticallyupgrade the software. During that time, ping the PiXORD NVS until getconstant reply, which means system had completed upgrading andrebooting, then open browser to verify the software version been updated.Note: If FTP session quits immediately after issued by command, you shouldcontinue pinging PiXORD NVS instantly. If PiXORD NVS replies to the pingcommand right after pinging, it means PiXORD NVS may not enter theself-programming stage to verify the software version. If not updated, then youshould reboot PiXORD NVS and back to step 3 to try againC:\temp>ftp 192.168.0.200Connected to 192.168.0.200.220 192.168.0.200 PiXORD FTP server (ARM_BE - V3.0.H) ready.User (192.168.0.200:(none)): root331 Password required for root.Password: bin200 Type set to I.ftp> put flash.bin200 PORT command successful.52 / 88
150 Opening BINARY mode data connection for flash.bin226 Transfer complete.ftp: 2097152 bytes sent in 10.11Seconds 207.43Kbytes/sec.ftp> bye221 Goodbye.
Page 1 and 2: PiXORD241/240/200/205/120/100/126/1
Page 3 and 4: 5.1.1 Configurations Overview......
Page 5 and 6: 1 Introduction1.1 What is PiXORD Ne
Page 7 and 8: 2 Physical Connections2.1 Front Pan
Page 9 and 10: 2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12: 3 Installation3.1 System Requiremen
Page 13 and 14: 3.3 Network Camera Installation Pro
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51: 6 Appendix6.1 Upgrading the Softwar
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64: ‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70: ‣ Weight0.93 kg, excluding power
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78: 6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80: - DirectX 9.0c‣ Security- Three-l
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?