User's Manual - Pixord

More documents

Recommendations

Info

‣ GPIO Terminal BlockPinName1 EXTVCC2 485A3 485B4 Relay_COM5 Relay_NO6 GPIN17 GPIN28 GPIN39 GPIN410 GND‣ Pin Number: External VCC: This pin outputs unregulated 10V when power on with AC 9V1A adapter, it may be used to drive external relay or sensor which is convenientto install for users.For rack mount application, it could be connected with external regulated DC10-24 Volt as system power. In this situation, we must not connect the ACadapter.Caution: The electric current can’t exceed 200mA when the external VCCoutputs to drive external devices. Furthermore, over loading will cause thedamage of AC adapter or internal components. If using external DC to input tosystem as power supply, it must provided in the specifications which regulatedDC 10~24V, >10W ; otherwise, it will cause system damaged ormalfunctioned.58 / 88
485A485BTo connect with external PTZ devices, please contact your dealer/distributor toget the information of the supported PTZ models.Relay_COMRelay Common point.Relay_NORelay Normal Open point. It will set to on (Short with Relay_COM) when setGPIO output high.GPIN1GPIN2GPIN3GPIN4Photo-coupled GPIO Input 1~4. Input high when opening the connection; inputlow when sinking more than 10mA or shorting to pin 10 (GND).GPIN4 is also used for Emergency Factory Default.GNDSystem Ground is also connected to chassis as frame ground.‣ RS-232 COM1 (9 Pin D-SUB male connector)Pin Name Dir Description1 CD ← Carrier Detect2 RXD ← Receive Data3 TXD → Transmit Data4 DTR → Data Terminal Ready5 GND — System Ground6 DSR ← Data Set Ready7 RTS → Request to Send8 CTS ← Clear to Send9 RI ← Ring Indicator59 / 88
Page 1 and 2:
PiXORD241/240/200/205/120/100/126/1
Page 3 and 4:
5.1.1 Configurations Overview......
Page 5 and 6:
1 Introduction1.1 What is PiXORD Ne
Page 7 and 8: 2 Physical Connections2.1 Front Pan
Page 9 and 10: 2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12: 3 Installation3.1 System Requiremen
Page 13 and 14: 3.3 Network Camera Installation Pro
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57: ‣ The IP address is located withi
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64: ‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70: ‣ Weight0.93 kg, excluding power
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78: 6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80: - DirectX 9.0c‣ Security- Three-l
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site
show all

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?