User's Manual - Pixord

More documents

Recommendations

Info

Support BLC, Exposure, Flicker, WB (3 modes) adjustment (PiXORD 205 only)‣ Build in support of DC-Driver auto iris lens, level adjustment supported(Exclude PiXORD 205).2.2 Rear Panel2.2.1 PiXORD IVSPiXORD 4000‣ Camera1~4:The PiXORD 4000 with Four BNCs for video signal input, the PiXORD 2000 withTwo BNCs for video signal input, the PiXORD 1000 with one BNC for video signalinput.‣ DIP Switch 1~4:Four segments of 75Ω impedance match switch, switch 1 match to camera oneand so on. Switch to “on” position when peer-to-peer connected with Cameras orother sources. Set to “off” position when video source paralleled with other 75Ωload (e.g. TV, VCR).‣ Com1 (DTE DSUB 9 pin Male connector):Capable of connecting to system console (default), voice server, or to externalmodem. Signal description in Appendix E -I/O & COM port Connectors.‣ Com2 (DCE DSUB 9 pin Female connector):Capable of connecting to PTZ devices, this port shares same electrical signal pathwith RS-485 port (refer to Appendix E -I/O & COM port Connectors), so it will bedisabled when setting to RS-485 mode.‣ IO Terminal Block:See Appendix E -I/O & COM port Connectors for detailed description.‣ Ethernet:RJ-45 Connector for connection of a twisted pair category 5 cable (StandardIEEE802.3 10BaseT).‣ AC 9V:AC Power input, specification with 9V AC 1A.8 / 88
2.2.2 PiXORD NCPiXORD 100 PiXORD 120/126/128PiXORD 200/205 PiXORD 240/241‣ Ethernet:RJ-45 Connector for connection of a twisted pair category 5 cable (StandardIEEE802.3 10BaseT).‣ DC 12V (PiXORD 100/120/126/128 only):DC Power input, specification with 12V DC 1A.‣ PS (PiXORD 200/240/241/205 only):AC Power input, specification with 14V/13.8V.‣ PWR LED:Power On: constant red.Emergency factory default (Appendix C - Emergency Factory Default): Blinkingorange (i.e. red mixed with green).‣ NETWORK LED:Network Link (connected): Constant red.Networks have activities: Blinking red.Data sent out from server: Blinking green.Network disconnected: Constant slow blinking green.Upgrading software (Appendix A - Upgrading the Software): Constant blinkingorange from slow to fast.9 / 88
Page 1 and 2: PiXORD241/240/200/205/120/100/126/1
Page 3 and 4: 5.1.1 Configurations Overview......
Page 5 and 6: 1 Introduction1.1 What is PiXORD Ne
Page 7: 2 Physical Connections2.1 Front Pan
Page 11 and 12: 3 Installation3.1 System Requiremen
Page 13 and 14: 3.3 Network Camera Installation Pro
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60:
485A485BTo connect with external PT
Page 61 and 62:
‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64:
‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66:
‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68:
6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70:
‣ Weight0.93 kg, excluding power
Page 71 and 72:
‣ Operating Temperature5 °C~50°
Page 73 and 74:
- Video throughput: Up to 30 frames
Page 75 and 76:
‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78:
6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80:
- DirectX 9.0c‣ Security- Three-l
Page 81 and 82:
FTP image to remote site;E-mail ima
Page 83 and 84:
- One RS-232 serial port for extern
Page 85 and 86:
2x LEDs to indicate network and pow
Page 87 and 88:
6. HTTP server push to remote site
show all

User's Manual - Pixord

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?