User's Manual - Pixord

More documents

Recommendations

Info

- Four fully opto-isolated alarm inputs and one 3A,125VAC/30VDC Relay output‣ Network Interface- Ethernet (10/100 Base-T)‣ Image Compression- JPEG; Motion JPEG‣ Video Adjustment- Brightness, Contrast, Hue, Saturation, Quality Level adjustment‣ Protocols- TCP/IP, UDP, ARP, ICMP, HTTP, FTP, Telnet, SMTP, DHCP‣ Max. Resolution- NTSC: 704x480(Single), 352x240(Quad)- PAL: 704x576(Single), 352x288(Quad)‣ Performance- Network throughput: Max. up to 800K bytes per second, 30 connectionssimutaneously- Video throughput: Up to 30 frames per second / Single Video‣ Event Trigger & Action- Programmable Event Script with Wizard supported.- Triggered by: Time (Frequency) / GPIO Input/ Motion Detection/ Video/ NetworkConnection/ CGI etc.- Action: Store image to internal buffer (2M Bytes pre- and post-alarm);FTP image to remote site;E-mail image to specific account;HTTP server push to remote site; relay output to control external devices; etc.‣ Installation- Assign IP address: using ARP & Ping or IP-Installer software‣ Software Upgrade- Local or Remote software up-gradable using FTP- Custom web contents updated via FTP & Telnet‣ System Requirements- Windows 2000 SP4 or Windows XP/Windows ME/Windows 98- Internet Explorer 6.078 / 88
- DirectX 9.0c‣ Security- Three-layer Password Protection‣ Operating Temperature- 5 °C~50°C (40°F~125°F)‣ Operating Humidity- 20 ~80 %‣ Input Voltage- DC 12V , 1A‣ Power Consumption
Page 1 and 2:
PiXORD241/240/200/205/120/100/126/1
Page 3 and 4:
5.1.1 Configurations Overview......
Page 5 and 6:
1 Introduction1.1 What is PiXORD Ne
Page 7 and 8:
2 Physical Connections2.1 Front Pan
Page 9 and 10:
2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12:
3 Installation3.1 System Requiremen
Page 13 and 14:
3.3 Network Camera Installation Pro
Page 15 and 16:
3.4 P128 Installation Procedure3.4.
Page 17 and 18:
‣ Adjust VR1 to set Infrared LED
Page 19 and 20:
3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22:
Enter “http://192.168.0.200” in
Page 23 and 24:
3.7.4 Verify the IP Address and Ope
Page 25 and 26:
4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64: ‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70: ‣ Weight0.93 kg, excluding power
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77: 6.7.6 PiXORD 200‣ Video Channel1
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site
show all

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?