User's Manual - Pixord

More documents

Recommendations

Info

Relay_NO shorts with Relay_COMGPIN1GPIN2GPIN3GPIN4Photo-coupled GPIO Input 1~4. The input is on when the connection is closed.GPIN4 is also used for Emergency Factory Default (Appendix C - EmergencyFactory Default ).TXD: Output to external PTZRXD: Input from external PTZDTR: Output to external PTZDSR: Input from external PTZGNDSystem Ground.EXT VIDEOExternal video input combines with DIP switch 1 to select internal /externalvideo source. DIP switch 2 is to do impendence match once select to externalvideo as input source.6.5.3 PiXORD 200/240/241/205The GPIO MINI DIM contains four GPIO inputs, one GPIO output as relay junction,and one RS-485 port. A PTZ device can connect directly to the PiXORD NC via theRS-485 port. And, the following pictures indicate the Pin direction:62 / 88
‣ GPIO MINI-DINPinName1 GPIN12 GPIN23 485B4 485A5 GND6 Relay_COM7 Relay_NO8 GPIN39 GPIN4‣ COM port MINI-DINPinName1 CD2 RXD3 TXD4 DSR5 GND6 DTR7 RTS8 CTS9 RI6.6 Lenses ReplacementThe PiXORD NC supports any standard C/CS lens, including full DC-Iris lens. You canreplace the built-in lens with any lens you like. Since the PiXORD NC is supplied with aCS-mount, any stand C or CS lens typically used in the surveillance industry can beused. Follow the instruct ions below to fit any C or CS type lens:‣ Use Normal LensesCS-mount lens mode is the standard type. When using C-mount lens, please usethe CS-C conversion Ring.63 / 88
Page 1 and 2:
PiXORD241/240/200/205/120/100/126/1
Page 3 and 4:
5.1.1 Configurations Overview......
Page 5 and 6:
1 Introduction1.1 What is PiXORD Ne
Page 7 and 8:
2 Physical Connections2.1 Front Pan
Page 9 and 10:
2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12: 3 Installation3.1 System Requiremen
Page 13 and 14: 3.3 Network Camera Installation Pro
Page 15 and 16: 3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61: ‣ GPIO Terminal BlockPinName1 EXT
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67 and 68: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 69 and 70: ‣ Weight0.93 kg, excluding power
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78: 6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80: - DirectX 9.0c‣ Security- Three-l
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site
show all

User's Manual - Pixord

Create successful ePaper yourself

Delete template?

Save as template?