User's Manual - Pixord

More documents

Recommendations

Info

‣ PerformanceVideo through put : Up to 30 frames/ secondNetwork through put : Max. up to 800 K Bytes per Second‣ Event Trigger & ActionProgrammable Event Script with Wizard supported.Triggered by: Time(Frequency) / GPIO Input/ Motion DetectionAction : - Store image to internal buffer- FTP image to remote site- E-mail image to specify account- relay output to control external devices‣ InstallationAssign IP address: using ARP/ or Via RS-232 or IP Installer‣ Software UpgradeLocal or Remote software upgradable using FTPCustom web contents updated via FTP & Telnet‣ System RequirementsWindows 2000 SP4 or Windows XP/Windows ME/Windows 98Internet Explorer 6.0DirectX 9.0c‣ SecurityThree-layer Password Protection‣ Operating Temperature5 °C~50°C (40°F~125°F)‣ Operating Humidity20 ~80 %‣ Input VoltageDC 12 V‣ Power Consumption
‣ Weight0.93 kg, excluding power supply6.7.3 PiXORD 4000/4200PiXORD 4000PiXORD 4200‣ Video Input4 Channels1.0 Vp-p, 75, Composite, BNC, Auto detection NTSC/PAL‣ HardwareCPU: 32 Bits RISC ProcessorROM: 2M Bytes FlashROMRAM: 16M Bytes SDRAMWatchDog: Chip to monitor out tolerance system voltage and abnormal programexecutionTwo RS-232 serial ports, one for external modem, one for PTZcamera/PC/RS-485 ; -(PiXORD 4000)One RS-232 serial port for external console; One RS-232/485 port for PTZ(pan/tilt/zoom) camera control -(PiXORD 4200)One RJ-45 for 10/100 Mbps EthernetTwo LEDs to indicate network and power/system statusGPIO with fully opto-isolated four alarm inputs and one relay output69 / 88
Page 1 and 2:
PiXORD241/240/200/205/120/100/126/1
Page 3 and 4:
5.1.1 Configurations Overview......
Page 5 and 6:
1 Introduction1.1 What is PiXORD Ne
Page 7 and 8:
2 Physical Connections2.1 Front Pan
Page 9 and 10:
2.2.2 PiXORD NCPiXORD 100 PiXORD 12
Page 11 and 12:
3 Installation3.1 System Requiremen
Page 13 and 14:
3.3 Network Camera Installation Pro
Page 15 and 16:
3.4 P128 Installation Procedure3.4.
Page 17 and 18: ‣ Adjust VR1 to set Infrared LED
Page 19 and 20: 3.6 Assign IP Address by ARP3.6.1 N
Page 21 and 22: Enter “http://192.168.0.200” in
Page 23 and 24: 3.7.4 Verify the IP Address and Ope
Page 25 and 26: 4 PiXORD NVS Home Page4.1 Browsing
Page 27 and 28: 5 PiXORD NVS Configuration Page5.1
Page 29 and 30: ‣ Event ConfigurationsFunctions D
Page 31 and 32: PiXORD NVS provides 3- layer user s
Page 33 and 34: 5.2.4 System commands‣ Load Defau
Page 35 and 36: devices which could access up to 65
Page 37 and 38: ‣ Dynamic DNS Activate: Click on
Page 39 and 40: 5.4 I/O Configuration5.4.1 Serial P
Page 41 and 42: 5.5 Video5.5.1 Time StampDisplay Ti
Page 43 and 44: Click "Save Changes" bottom if need
Page 45 and 46: 5.5.5 CCD Module Settings (PiXORD 2
Page 47 and 48: Note: The programmable event script
Page 49 and 50: 5.7 Voice Management5.7.1 Voice Adj
Page 51 and 52: 6 Appendix6.1 Upgrading the Softwar
Page 53 and 54: 150 Opening BINARY mode data connec
Page 55 and 56: 3.0.0/WWW/images.Note: Any file upl
Page 57 and 58: ‣ The IP address is located withi
Page 59 and 60: 485A485BTo connect with external PT
Page 61 and 62: ‣ GPIO Terminal BlockPinName1 EXT
Page 63 and 64: ‣ GPIO MINI-DINPinName1 GPIN12 GP
Page 65 and 66: ‣ Video Input1 Channels1.0 Vp-p,
Page 67: 6.7.2 PiXORD 2000PiXORD 2000‣ Vid
Page 71 and 72: ‣ Operating Temperature5 °C~50°
Page 73 and 74: - Video throughput: Up to 30 frames
Page 75 and 76: ‣ Hardware- CPU: 32 Bits RISC Pro
Page 77 and 78: 6.7.6 PiXORD 200‣ Video Channel1
Page 79 and 80: - DirectX 9.0c‣ Security- Three-l
Page 81 and 82: FTP image to remote site;E-mail ima
Page 83 and 84: - One RS-232 serial port for extern
Page 85 and 86: 2x LEDs to indicate network and pow
Page 87 and 88: 6. HTTP server push to remote site
show all

User's Manual - Pixord

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?