Register your product now - Radiometer Analytical

More documents

Recommendations

Info

6.7.4 Set up <strong>your</strong> cellIf you run a sequence with the RCB200 Resistor Capacitor Box, there is no need toedit the Cell setup parameters: skip to next paragraph (Other settings).If you run a sequence on a real cell, perform the following operations:. Select the “Settings” menu then the “Cell setup” command.. Specify the reference electrode you are using (select a predefined type or select“User defined”). Enter the area of the working and auxiliary electrodes (“WORK(WE) – Area” and “AUX (CE) – Area”). The other settings are to be entered ifyou intend to calculate a corrosion rate or run a General corrosion (Rp) method.In all other cases, you do not need to make any changes to the other Cell setupsettings.For more information, consult the Help file, keyword index:Cell setup.176VoltaLab 21/06/10/40/50/80Section 6, Chapter 7: HVB100 High Voltage Booster
6.7.5 Set up the other settingsSet up the other settings parameters as explained in section 3 “Getting started”.For more information, consult the Help file, keyword index:Other settings.6.7.6 Running the experimentSwitch on the PGZ/PST and HVB100.Press the “Cell” button on PGZ/PST and HVB100, then start the experiment fromVoltaMaster 4.6.7.7 TroubleshootingThe pilot lamp “ON” is not lit when the HVB100 is switched onCheck the power supply circuit (mains socket, mains cable, fuse and On/Offswitch). Replacement of the fuses is described below.Check that the mains voltage selection switch on the rear panel of the HVB100 isset to the position corresponding to the mains voltage: too low or too high voltagesare equally harmful. Please refer to Section 3 “Getting Started”, paragraph 3.1.1.Replacing the fuses:Switch off the HVB100 (“On/Off” switch set to “Off”) and find the fuse holder on therear panel.Note: Secondary fuses are mounted on the printed circuit. The replacement ofthese fuses must be performed by a HACH LANGE service representative (theinstrument casing must be opened).2. Remove the fuse holderHook1. Remove themains cableFuse rating T3.15A L250V3. Replace the spent fuse by a new one of the same rating4. Fit the fuse holder back in place (check that the hook is fitted correctly)Warning!Always replace the fuse with the same type and rating.VoltaLab 21/06/10/40/50/80 177Section 6, Chapter 7: HVB100 High Voltage Booster
Page 1 and 2:
Register your product nowTo keep up
Page 3 and 4:
ContentsRegister your product now 1
Page 5 and 6:
1. General presentationDear Custome
Page 7 and 8:
Precautionary LabelsRead all labels
Page 9:
1.3 VoltaLab 21 Economical Electroc
Page 12 and 13:
1.6 VoltaLab 40 Dynamic Electrochem
Page 14:
1.8 VoltaLab 80 Universal Electroch
Page 20:
Edit the Other settings parameters.
Page 23 and 24:
2.5 Uninstalling VoltaMaster 4Volta
Page 25 and 26:
3. Getting startedFor a VoltaLab 10
Page 28:
For a VoltaLab 06RS232 cable9-pin f
Page 31 and 32:
3.3 User identificationIf you selec
Page 33 and 34:
3.5 Set up your instrumentIf you se
Page 35 and 36:
3.7 Set up the Other settings param
Page 37 and 38:
4. VoltaMaster 44.1 The VoltaMaster
Page 39 and 40:
Curve type bar - XX is the abscissa
Page 41:
4.2 Using the VoltaMaster 4 Help fi
Page 45 and 46:
4.3.1 Open Circuit PotentialThe Ope
Page 47 and 48:
Visual IFVA virtual front panel is
Page 49 and 50:
4.3.13 Pot. Dynamic EIS (Impedance)
Page 51 and 52:
4.3.17 Gal. Expert EIS (Impedance)T
Page 53 and 54:
4.3.22 Pot. Step by step CVStep by
Page 55 and 56:
4.3.28 Gal. Universal DPThe Gal. Un
Page 57 and 58:
4.3.34 Pot. Low Current CAA potenti
Page 59 and 60:
4.3.40 Auto. TrajectThe Auto. Traje
Page 61 and 62:
4.3.46 Standard calibrationThis met
Page 63 and 64:
4.3.47 Calibration by additionThis
Page 65 and 66:
4.3.53 Print ReportThe Print Report
Page 67 and 68:
The following guidances are given i
Page 69 and 70:
8. Save the sequenceThe initial dat
Page 71 and 72:
4.5.1 Before starting a sequenceChe
Page 73 and 74:
4.6 Processing curves to obtain res
Page 75 and 76:
4.6.1 Post run processing functions
Page 77 and 78:
InformationDisplay information on a
Page 79 and 80:
Evans plotDisplay the Evans diagram
Page 81 and 82:
4.7 PrintoutsThe Printpreview iconV
Page 83 and 84:
4.7.3 Preparing a printoutThe “Fi
Page 85 and 86:
4.7.5 Printing the parameters of an
Page 87:
4.7.6 Printing CurvesA curve or an
Page 90 and 91:
1. 20 curves maximun in a graphYou
Page 92 and 93:
6. Current disjunctionEffectsThe po
Page 94 and 95:
11. Out of range: -15 V to 15 VWhil
Page 96 and 97:
17. Vg overloadThis error message i
Page 98 and 99:
4.9 Troubleshooting list4.9.1 Chara
Page 100 and 101:
4.10 The ohmic drop compensation4.1
Page 102 and 103:
4.10.4 Running an experiment with a
Page 104 and 105:
CGgIPpQRSTZCalibration CV STGal. Un
Page 106 and 107:
Menu “File” (Routine setup mode
Page 108 and 109:
Menu “Settings” (Full and Super
Page 110 and 111:
Menu “File” (Routine setup mode
Page 112 and 113:
Menu “Settings” (Full and Super
Page 114 and 115:
5.1.1 The front panelsPGZ100 and PG
Page 116 and 117:
The “D/A OUT” socket (4)A DC vo
Page 118 and 119:
5.1.2 The rear panelsLINE FUSE T2A
Page 120 and 121:
4 connecting cords are used (see th
Page 122 and 123:
5.1.4 UseThe PGZ and PST potentiost
Page 124 and 125:
5. Background noise on measurements
Page 126 and 127: 5.1.7 Technical specificationsPGZ10
Page 128 and 129: PGZ301 PotentiostatRegulationCompli
Page 130 and 131: PGZ402 Universal PotentiostatRegula
Page 132 and 133: PST006 Educational PotentiostatRegu
Page 134 and 135: 5.1.8 CE MarkingThe PGZ100, PGZ301,
Page 136 and 137: the PGP201 internal signal generato
Page 138 and 139: 5.2.2 The rear panelLI-BATTERY3.6 V
Page 140 and 141: 5.2.3 InstallationElectrical safety
Page 142 and 143: 2. Connecting the computerSee Secti
Page 144 and 145: 3. User data lost - Press any keyTh
Page 146 and 147: 5.2.6 MaintenanceWarning!All cables
Page 148 and 149: 5.2.8 CE MarkingThe PGP201 complies
Page 150 and 151: If the EDI10000 is used:ONE(X) INI
Page 152 and 153: 3. To set another electrode rotatin
Page 154 and 155: Cables 1 to 4 are supplied in the C
Page 156 and 157: 6.3 Rotating Ring and Disc Electrod
Page 158 and 159: PGZ TwoWORKAUXREFCell ringCell AUXC
Page 160 and 161: 6.3.5 ConclusionIt is convenient an
Page 162 and 163: 1 PGZ/PST050 “REF.” socket to t
Page 164 and 165: 6.5.2 SettingsEstablish the serial
Page 166 and 167: 166VoltaLab 21/06/10/40/50/80Sectio
Page 168 and 169: Determine the peak and integrate th
Page 170 and 171: Determine the peak and integrate th
Page 172 and 173: 6.6 ABU901 AutoburetteThe ABU901 is
Page 174 and 175: RS232 cable9-pin female / 9-pin fem
Page 178 and 179: 6.7.8 Technical specifications - HV
Page 180 and 181: 6.8 HCB005 - HCB010 - HCB020 High C
Page 182 and 183: RS232CLINE FUSE T2A L250V120/230 Va
Page 184 and 185: If it is not the case (communicatio
Page 186 and 187: 6.8.5 Set up the other settingsSet
Page 188 and 189: Environmental conditionsInterior us
Page 190 and 191: 6.9 Additional units - PGZ402 E(X)
Page 192 and 193: Check that the electrical zero and
Page 194 and 195: Click the “Settings” button and
Page 196 and 197: 6.11 External signal generator - Vg
Page 198 and 199: 6.12 Measuring an A/D IN signalUsin
show all

Register your product now - Radiometer Analytical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?