1. First steps in Reaktor Core - Native Instruments

More documents

Recommendations

Info

9.2. Routing and merging Routing can be more or less CPU intensive depending on the situation and the platform. If you can avoid routing without adding other CPU-intensive operations to your structure, do so. Sometimes ES Ctl routing can be replaced by using Latches. If possible, do so. If you split the event path into two branches using a Router, it’s a good idea to merge the branches generated by the outputs of the Router: It’s also a good idea to merge to the incoming (unsplit) event to the Router: Merging is not necessarily done by using a Merge module. Any arithmetic or a similar module will do the job: Merging can also happen inside a macro (depending on its internal structure): It may be reasonable or necessary to merge the branches generated by different Routers, but beware of higher CPU loads in that case. 140 – REAKTOR CORE
9.3. Numerical operations Floating point addition, multiplication, subtraction, absolute value, and negation are generally the least CPU-intensive float operations. Integer addition, subtraction and negation are the least CPU-intensive integer operations. Integer absolute value is also more or less OK. DN Cancel currently uses plain addition, as you may remember. Float division, and integer multiplication and division are significantly more CPU intensive on average. It is advisable to group your operations in a way that the most CPU intensive ones get evaluated as rarely as possible. For example, if you need to compute normalized frequency by dividing the frequency in Hz by the sampling rate it could be reasonable to compute the reciprocal of the sampling rate first and multiply the frequency by the result: In the above structure, the division will be performed only when the sample rate changes, which should be pretty rare. Changes to the frequency will trigger only multiplication. Compare that to the more straightforward implementation of the same formula: where the division would be executed in response to every change of frequency. 9.4. Conversions between floats and integers Generally, avoid all unnecessary conversions between float and integer numbers. Depending on the platform such conversions could use significant amounts of CPU. The conversions that are necessary to do are OK, of course. Although the following structure might work as expected, in fact, there are two unnecessary conversions between integer and float types: REAKTOR CORE – 141
Page 1 and 2:
REAKTOR CORE Tutorial
Page 3 and 4:
Table of Contents 1. First steps in
Page 5 and 6:
Appendix D. Core cell ports .......
Page 7 and 8:
H.7. Audio Mix-Amp > Gain (dB) ....
Page 9 and 10:
H.88. Logic > GT / IGT ............
Page 11 and 12:
1. First steps in Reaktor Core 1.1.
Page 13 and 14:
You may also want to save core cell
Page 15 and 16:
1.3. Using core cells in a real exa
Page 17 and 18:
1.4. Basic editing of core cells No
Page 19 and 20:
You can shrink them back by right-c
Page 21 and 22:
or design of the module. Generally,
Page 23 and 24:
And here is an example of an event
Page 25 and 26:
converter. As a result, our control
Page 27 and 28:
The VCF section could be promising,
Page 29 and 30:
There’s only one kind of module y
Page 31 and 32:
As the name implies (and the info t
Page 33 and 34:
Now you can type some text into the
Page 35 and 36:
Instead of a nasty looking diagonal
Page 37 and 38:
Some types of processing, mixing fo
Page 39 and 40:
mix it with the delayed signal. Bec
Page 41 and 42:
0.02ms at 44.1kHz, even less at hig
Page 43 and 44:
The Latch and Bool C types of ports
Page 45 and 46:
In the value field type a new value
Page 47 and 48:
modules in the same way we did earl
Page 49 and 50:
2.5. Using audio as control signal
Page 51 and 52:
some primary-level event signals us
Page 53 and 54:
is always at full amplitude. At 1 t
Page 55 and 56:
The Gate2L, AND, and L2Gate modules
Page 57 and 58:
Here is a picture of a continuous s
Page 59 and 60:
3.3. Simultaneous events Consider t
Page 61 and 62:
3.4. Processing order As you have s
Page 63 and 64:
Event Inputs send core events to th
Page 65 and 66:
Of course, in this particular case
Page 67 and 68:
Now move the knob and watch the out
Page 69 and 70:
4.2. Object Bus Connections Object
Page 71 and 72:
As mentioned, the above structure i
Page 73 and 74:
constants would send their values a
Page 75 and 76:
4.4. Building an event accumulator
Page 77 and 78:
� ��
Page 79 and 80:
Now the reset works as specified. T
Page 81 and 82:
output values. Let’s try that wit
Page 83 and 84:
Should any files be found in this C
Page 85 and 86:
The name “Modulation”, although
Page 87 and 88:
5. Audio processing at its core 5.1
Page 89 and 90: 5.2. Sampling rate clock bus A coup
Page 91 and 92: We have already seen a structure bu
Page 93 and 94: connections will be marked as inval
Page 95 and 96: As you can see, the clock input of
Page 97 and 98: left which we cannot see from the o
Page 99 and 100: samples, we have to produce several
Page 101 and 102: 5.6. Other bad numbers Denormal num
Page 103 and 104: 6.28319 is 2*π, which is then divi
Page 105 and 106: 6. Conditional processing 6.1. Even
Page 107 and 108: In this version, the 0 output of th
Page 109 and 110: First we are going to build the cir
Page 111 and 112: default means use whatever precisio
Page 113 and 114: Switching between float and integer
Page 115 and 116: The output and all built-in modules
Page 117 and 118: The OBC chain at the bottom keeps t
Page 119 and 120: The speed of the number change in t
Page 121 and 122: And now the connection: The upper i
Page 123 and 124: This macro internally has an Index
Page 125 and 126: The four Write [] modules will take
Page 127 and 128: In general, you should also take ca
Page 129 and 130: � ��
Page 131 and 132: The size property of the array can
Page 133 and 134: So we include another macro for wra
Page 135 and 136: A new dialog will appear: What you
Page 137 and 138: Formal output precision Now that we
Page 139: 9. Building optimal structures As a
Page 143 and 144: Appendix A. Reaktor Core user inter
Page 145 and 146: Appendix B. Reaktor Core concept B.
Page 147 and 148: Appendix C. Core macro ports C.1. I
Page 149 and 150: Appendix D. Core cell ports D.1. In
Page 151 and 152: F.3. Math > - Produces the differen
Page 153 and 154: F.12. Bit > Bit OR Performs the bit
Page 155 and 156: that the module on the picture abov
Page 157 and 158: connected to the sidechain input. T
Page 159 and 160: Appendix G. Expert macros G.1. Clip
Page 161 and 162: G.12. Math > sqrt Square root appro
Page 163 and 164: G.24. Memory > Read [] Reads a valu
Page 165 and 166: Appendix H. Standard macros H.1. Au
Page 167 and 168: H.8. Audio Mix-Amp > Invert Inverts
Page 169 and 170: H.15. Audio Mix-Amp > XFade (lin) A
Page 171 and 172: H.22. Audio Shaper > Sine Shaper 4
Page 173 and 174: H.30. Control > Ctl Pan “Pans”
Page 175 and 176: H.38. Convert > ms2sec Converts the
Page 177 and 178: to positive. The allowed RM values
Page 179 and 180: H.53. EQ > Static Filter > 1-pole s
Page 181 and 182: H.62. EQ > Static Filter > 2-pole s
Page 183 and 184: H.70. Event Processing > Ctl2Gate C
Page 185 and 186: H.79. LFO > Random LFO Generates a
Page 187 and 188: H.88. Logic > GT / IGT Compares the
Page 189 and 190: Generates 4 phase-locked audio wave
Page 191 and 192:
H.105. Oscillators > Quad Osc Gener
Page 193 and 194:
H.112. VCF > Diode Ladder Diode-lad
Page 195 and 196:
I.4. Audio Shaper > Parabol Sat Sim
Page 197 and 198:
I.10. Control > Par Ctl Shaper Appl
Page 199 and 200:
I.17. EQ > HighShelf EQ 1-pole high
Page 201 and 202:
I.25. EQ > Static Filter > 2-pole s
Page 203 and 204:
I.33. Oscillator > 4-Wave Mst Gener
Page 205 and 206:
I.39. Oscillator > MultiWave Osc Ge
Page 207 and 208:
I.44. VCF > 2 Pole SV x3 S 2-pole s
Page 209 and 210:
Index A Array module ..............
show all

1. First steps in Reaktor Core - Native Instruments

Create successful ePaper yourself

Delete template?

Save as template?