Doktorski rad - FSB - Sveučilište u Zagrebu

LITERATURA
[1] D.W. CZIMMEK and L.W.SANDOR. "Economic and Technical Feasibility of
Copper- Nickel Sheating of Ship Hulls", Marine Technology, Vol.22, No.2, April
1985, pp.142-154.
[2] R.L. TOWNSIN et al. "Speed, Power and Roughness: The Economics of Outer
Bottom Maintenance", RINA 1980; pp. 459-483.
[3] J.A. MALONE et al. "Effects of Hull Foulants and Cleaning/Coating Practices on
Ship Performance and Economics"; SNAME, Transactions, Vol. 88, 1980., pp 75-101.
[4] C. S. SUBRAMANIAN et al: "A Study of Hydrodynamic Characteristics of Boundary
Layer With Algae Roghness"; Marine Technology, Vol.41-No.2 April 2004., pp.60-
66.
[5] E. NAESS: "Reduction of Drag Resistance caused by Surface Roughness and Marine
Fouling"; Norwegian Maritime Research; No.4/80; pp. 12-16.
[6] R.L. TOWNSIN et al.: "Fuel Economy due to Improvement in Ship Hull Surface
Condition", International Shipbuilding Progress, 33(383), 1986, pp.127-130.
[7] M. ATLAR et al.: "The Effect of a Foul Release Coating on Propeller Performance",
Marine technology, Vol.41, No.2, April 2004, pp.7-14.
[8] H.E. SAUNDERS : "Hydrodynamics in Ship Design"; The Society of Naval
Architects and Marine Engineers; Vol.2., New York, 1957; pp. 102-104.
[9] M. KREŠIĆ and B. HASKELL: "Effects of Propeller Design-Point Definition on the
Performance of a Propeller/Diesel Engine System with Regard to In-Service
Roughness and Weather Conditions "SNAME Transactions, Vol.91, 1983.; pp.195-
224.
[10] R.L. TOWNSIN : "Workshop-Calculating the Cost of Marine Surface Roughness on
Ship Performance"; 32nd WEGEMT School on Marine Coatings; University of
Plymouth; 10-14 July 2000. pp.119-127.
[11] A.J. SMITS et al.: "Some Experiments on Artificially Roughened Lucy Ashton
Geosims", Journal of Ship Research, Vol.24, No.3, Sept.1980, pp.170-180.
[12] INTERNATIONAL COATINGS: "Hull Roughness Surveys"; Shipping
World&Shipbuilder, October 2003., pp.41-42.
[13] D. JONES: "Afloat Maintenance, the Control of Marine Fouling and the Care of
Coatings Underwater"; WEGEMT School, University of Plymouth, UK; Plymouth,
2000; pp. 207-220.
[14] D. BYRNE: "Hull Roughness of Ships in Service", M.Sc. Thesis, University of
Newcastle upon Tyne, UK, 1981.
[15] B.O. SILLERUD "The Effect of Speed Loss in Service on Ship FreightIncome and
Fuel Economy"; Norwegian Maritime Research; No.2/1980; pp. 13-19.
[16] C. S. SUBRAMANIAN et al: "Noncontact Measurements of Marine Biofouling";
Marine Technology, Vol.41-No.2. April 2004., pp.67-73.
[17] R.E.A. ARNDT et al "Influence of Surface Irregularities on Cavitation Performance";
Journal of Ship Research, Vol.23, No.3, Sept.1979; pp.157-170.
[18] R.L. TOWNSIN et al. "Hull Condition, Penalties and Palliatives for Poor
Performance"; 4 th International Congress on Marine Corrosion and Fouling, 1976.
[19] E. NAESS: "Reduction of Drag Resistance caused by Surface Roughness and Marine
Fouling"; Norwegian Maritime Research; No. 4/80; pp. 12-16.
[20] A.K. LEWKOWICZ and A.J. MUSKER: "The Surface Roughness and Turbulent
Wall Friction on Ship-Hulls: Interaction in the Viscous Sublayer"; International
Symposium on Ship Viscous Resistance, SSPA, Goeteborg, 1978.; pp.10.1-10.22.
[21] R.L. TOWNSIN et al.: "Estimating the Technical and Economic Penalties of Hull and
Propeller Roughness"; SNAME Transactions, Vol.89, 1981, pp.295-318.
225