Compact / CANmotion /Motion Controller ... - Schneider Electric

More documents

Recommendations

Info

Download the Controller and HMI project 1 NOTE: For the initial download, the Magelis HMI requires the latest version of the runtime kernel and the Controller address. This is accomplished by using Vijeo Designer for the initial download This first download is described in the following steps. If this is not the initial Magelis HMI download go direct to step 7. 2 In Vijeo Designer, under the Property Inspector select Download via Ethernet. Note: The PC should be connected with the HMI via the Ethernet switch TCSESU053FN0. The IP address of the target machine can be set by using the Offline Configuration Menu of the XBTGT HMI. For more detail, please see the online help of Vijeo Designer. Performance CANmotion LMC058 Schneider Electric 110
3 Select Build → Download All. 4 The VDPLoad dialog box shows; Runtime versions do not match. Start the download of the new version by clicking on Yes. 5 The actual state of the download is displayed. 6 After the download, change the Download option back to SoMachine. Performance CANmotion LMC058 Schneider Electric 111
Page 1 and 2:
This document is based on European
Page 3 and 4:
Important Information NOTICE Read t
Page 5 and 6:
CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8:
Abbreviations Abbreviation AC CB CF
Page 9 and 10:
Application Source Code Introductio
Page 11 and 12:
System Introduction The system chap
Page 13 and 14:
Cabinet Technical Data Input Mains
Page 15 and 16:
Installation Introduction This chap
Page 17 and 18:
Remote cabinet interior Performance
Page 19 and 20:
Notes The components designed for i
Page 21 and 22:
Power supply Phaseo ABL8RPS24050 24
Page 23 and 24:
Motor Circuit Breaker GV2L08 and GV
Page 25 and 26:
Modicon LMC058 Motion Controller em
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Modicon LMC058 Motion Controller Te
Page 33 and 34:
Modicon LMC058 Motion Controller Ex
Page 35 and 36:
Servo Drive Lexium32 LXM32AD18M2 1-
Page 37 and 38:
Servo Drive Lexium32 LXM32AD18M2 Co
Page 39 and 40:
Servo Drive Lexium32 LXM32AD18M2 Wi
Page 41 and 42:
Servo Motor for Lexium32 BSH0702P02
Page 43 and 44:
Lexium SD3 Stepper motor drive SD32
Page 45 and 46:
Variable Speed Drive Altivar 312 AT
Page 47 and 48:
Encoder cable for Altivar 71 XCCPM2
Page 49 and 50:
1. Brushless DC motor 2. Electronic
Page 51 and 52:
Integrated drive Lexium Lexium ILA
Page 53 and 54:
Harmony Tower light XVBC... Solid s
Page 55 and 56:
Software General The main programmi
Page 57 and 58:
Altivar 71 Modbus / CANopen port No
Page 59 and 60: Advantys OTB CANopen Port OTB1C0DM9
Page 61 and 62: Lexium SD3 CANmotion port Node ID:
Page 63 and 64: CANopen connector VW3CANKCDF90T, VW
Page 65 and 66: ConneXium Ethernet 5 port switch TC
Page 67 and 68: CANopen cabling component *1 - TSX
Page 69 and 70: Implementation Introduction The imp
Page 71 and 72: Communication Introduction This cha
Page 73 and 74: Datalink LMC058 (CANopen-Master, #1
Page 75 and 76: Create a new project 1 To create a
Page 77 and 78: 3 The Devices folder now displays t
Page 79 and 80: Add the CANopen fieldbus 1 Right cl
Page 81 and 82: 4 Press Close Add CANopen Devices 1
Page 83 and 84: Performance CANmotion LMC058 Schnei
Page 85 and 86: 3 The new devices are now listed in
Page 87 and 88: OTB CANopen Configuration 1 Double
Page 89 and 90: 2 Change the Node ID to 23 and sele
Page 91 and 92: 2 Select: CANmotion Click on Add De
Page 93 and 94: 2 Select the device they connected
Page 95 and 96: 4 Double click on motion section of
Page 97 and 98: 4 The upper frame displays the decl
Page 99 and 100: 12 In the Input Assistant select Gl
Page 101 and 102: 4 To add a POU to the motion task d
Page 103 and 104: Configure Controller HMI Data Exch
Page 105 and 106: 4 Select Gateway-1 and click on Sca
Page 107 and 108: Communication Setting HMI PC 1 To
Page 109: Build Application 1 To build the ap
Page 113 and 114: Login to Controller 1 To login to t
Page 115 and 116: HMI Introduction This application u
Page 117 and 118: Communication settings 1 To set the
Page 119 and 120: 4 Click on the bulb icon (as indica
Page 121 and 122: 2 The “Safety” page shows the s
Page 123 and 124: Devices Introduction This chapter d
Page 125 and 126: CANopen settings 1 Using the button
Page 127 and 128: Brake settings 1 The r2 relay outpu
Page 129 and 130: 6 After changing the configuration
Page 131 and 132: Lexium 32A Introduction Note The LX
Page 133 and 134: TeSysU Introduction This chapter co
Page 135 and 136: Advantys OTB General The extended O
Page 137 and 138: 6 Click on the I/O Image Overview i
Page 139 and 140: 12 Select Network Configuration SyC
Page 141 and 142: Application Basics Usually packagin
Page 143 and 144: Photo-electric sensor OsiSense (Nep
Page 145 and 146: AnalogTensionControlATV_Motion The
Page 147 and 148: DigitalTensionControlATV_Motion The
Page 149 and 150: TemperatureControl The function blo
Page 151 and 152: FlyingShear_Motion The FlyingShear_
Page 153 and 154: Clamping_Motion The Clamping_Motion
Page 155 and 156: Automation Components Hardware-Comp
Page 157 and 158: Hardware-Components Pos. Qty Descri
Page 159 and 160: CANopen and Ethernet Hardware-Compo
Page 161 and 162:
Component Features Components Compa
Page 163 and 164:
Lexium Integrated Drive ILE with Br
Page 165 and 166:
Preventa safety module: XPSAC5121 M
Page 167 and 168:
Advantys Configuration Software STB
show all

Compact / CANmotion /Motion Controller ... - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?