Compact / CANmotion /Motion Controller ... - Schneider Electric

More documents

Recommendations

Info

Changing the Access Level LAC 1 To set the parameters for the brake function a higher access level (L3) is required. 2 To go to expert mode L3: Select CtL [COMMAND] and press enter Select LAC [ACCESS LEVEL] and press enter L1 (Level 1) is displayed Select L3 (Level 3) and press enter for 2 seconds to set the new level. Return to the LAC with ESC. Return to the CtL with ESC. Performance CANmotion LMC058 Schneider Electric 126
Brake settings 1 The r2 relay output is used for brake control. 2 To assign the r2 relay output : Select FUn- [APPLICATION FUNCT.] and press enter Select bLC- [BRAKE LOGIC CONTROL] and press enter Select bLC [BRAKE ASSIGNMENT] and press enter Select r2 and press enter. Set the parameters to the values shown here on the right. Note: These parameters are for the test machine only. They are NOT VALID for every machine. After all parameters are set return to the bLC with ESC. Return to the bLC- with ESC. Return to the FUn with ESC. Performance CANmotion LMC058 Schneider Electric 127
Page 1 and 2:
This document is based on European
Page 3 and 4:
Important Information NOTICE Read t
Page 5 and 6:
CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8:
Abbreviations Abbreviation AC CB CF
Page 9 and 10:
Application Source Code Introductio
Page 11 and 12:
System Introduction The system chap
Page 13 and 14:
Cabinet Technical Data Input Mains
Page 15 and 16:
Installation Introduction This chap
Page 17 and 18:
Remote cabinet interior Performance
Page 19 and 20:
Notes The components designed for i
Page 21 and 22:
Power supply Phaseo ABL8RPS24050 24
Page 23 and 24:
Motor Circuit Breaker GV2L08 and GV
Page 25 and 26:
Modicon LMC058 Motion Controller em
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Modicon LMC058 Motion Controller Te
Page 33 and 34:
Modicon LMC058 Motion Controller Ex
Page 35 and 36:
Servo Drive Lexium32 LXM32AD18M2 1-
Page 37 and 38:
Servo Drive Lexium32 LXM32AD18M2 Co
Page 39 and 40:
Servo Drive Lexium32 LXM32AD18M2 Wi
Page 41 and 42:
Servo Motor for Lexium32 BSH0702P02
Page 43 and 44:
Lexium SD3 Stepper motor drive SD32
Page 45 and 46:
Variable Speed Drive Altivar 312 AT
Page 47 and 48:
Encoder cable for Altivar 71 XCCPM2
Page 49 and 50:
1. Brushless DC motor 2. Electronic
Page 51 and 52:
Integrated drive Lexium Lexium ILA
Page 53 and 54:
Harmony Tower light XVBC... Solid s
Page 55 and 56:
Software General The main programmi
Page 57 and 58:
Altivar 71 Modbus / CANopen port No
Page 59 and 60:
Advantys OTB CANopen Port OTB1C0DM9
Page 61 and 62:
Lexium SD3 CANmotion port Node ID:
Page 63 and 64:
CANopen connector VW3CANKCDF90T, VW
Page 65 and 66:
ConneXium Ethernet 5 port switch TC
Page 67 and 68:
CANopen cabling component *1 - TSX
Page 69 and 70:
Implementation Introduction The imp
Page 71 and 72:
Communication Introduction This cha
Page 73 and 74:
Datalink LMC058 (CANopen-Master, #1
Page 75 and 76: Create a new project 1 To create a
Page 77 and 78: 3 The Devices folder now displays t
Page 79 and 80: Add the CANopen fieldbus 1 Right cl
Page 81 and 82: 4 Press Close Add CANopen Devices 1
Page 83 and 84: Performance CANmotion LMC058 Schnei
Page 85 and 86: 3 The new devices are now listed in
Page 87 and 88: OTB CANopen Configuration 1 Double
Page 89 and 90: 2 Change the Node ID to 23 and sele
Page 91 and 92: 2 Select: CANmotion Click on Add De
Page 93 and 94: 2 Select the device they connected
Page 95 and 96: 4 Double click on motion section of
Page 97 and 98: 4 The upper frame displays the decl
Page 99 and 100: 12 In the Input Assistant select Gl
Page 101 and 102: 4 To add a POU to the motion task d
Page 103 and 104: Configure Controller HMI Data Exch
Page 105 and 106: 4 Select Gateway-1 and click on Sca
Page 107 and 108: Communication Setting HMI PC 1 To
Page 109 and 110: Build Application 1 To build the ap
Page 111 and 112: 3 Select Build → Download All. 4
Page 113 and 114: Login to Controller 1 To login to t
Page 115 and 116: HMI Introduction This application u
Page 117 and 118: Communication settings 1 To set the
Page 119 and 120: 4 Click on the bulb icon (as indica
Page 121 and 122: 2 The “Safety” page shows the s
Page 123 and 124: Devices Introduction This chapter d
Page 125: CANopen settings 1 Using the button
Page 129 and 130: 6 After changing the configuration
Page 131 and 132: Lexium 32A Introduction Note The LX
Page 133 and 134: TeSysU Introduction This chapter co
Page 135 and 136: Advantys OTB General The extended O
Page 137 and 138: 6 Click on the I/O Image Overview i
Page 139 and 140: 12 Select Network Configuration SyC
Page 141 and 142: Application Basics Usually packagin
Page 143 and 144: Photo-electric sensor OsiSense (Nep
Page 145 and 146: AnalogTensionControlATV_Motion The
Page 147 and 148: DigitalTensionControlATV_Motion The
Page 149 and 150: TemperatureControl The function blo
Page 151 and 152: FlyingShear_Motion The FlyingShear_
Page 153 and 154: Clamping_Motion The Clamping_Motion
Page 155 and 156: Automation Components Hardware-Comp
Page 157 and 158: Hardware-Components Pos. Qty Descri
Page 159 and 160: CANopen and Ethernet Hardware-Compo
Page 161 and 162: Component Features Components Compa
Page 163 and 164: Lexium Integrated Drive ILE with Br
Page 165 and 166: Preventa safety module: XPSAC5121 M
Page 167 and 168: Advantys Configuration Software STB
show all

Compact / CANmotion /Motion Controller ... - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?