(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

Safety Symbols and Terms The following safety terms are used in this manual: The WARNING heading in this manual explains dangers that could result in personal injury or death. The CAUTION heading in this manual explains hazards that could damage the instrument. In addition, a NOTES heading gives information to the user that may be beneficial in the use of this instrument. GENERAL WARNINGS AND CAUTIONS The following general warnings and cautions are applicable to this instrument: WARNING This instrument is intended for use by qualified personnel who recognize shock hazards or laser hazards and are familiar with safety precautions required to avoid possible injury. Read the instruction manual thoroughly before using, to become familiar with the instrument’s operations and capabilities. WARNING The American National Safety Institute (ANSI) states that a shock hazard exists when probes or sensors are exposed to voltage levels greater then 42VDC or 42V peak AC. Do not exceed 42V between any portion of the Model 2832-C (or any attached detector or probe) and earth ground or a shock hazard will result. CAUTION There are no user serviceable parts inside the Model 2832-C. Work performed by persons not authorized by <strong>Newport</strong> may void the warranty. For instructions on obtaining warranty repair or service please refer to Section 5 of this manual. ix
Definitions A amps AC alternating current ADC analog-to-digital converter BAT battery option BIC biconic fiber connector BNC standard coaxial connector type C degrees Centigrade DC direct current F degrees Fahrenheit fA femtoamps Hz hertz (cycles per second) I-V current-to-voltage converter kHz kilohertz LSD least significant digit k kiloOhms mA milliamps mV millivolts nA nanoamps nF nanofarads nm nanometers pA picoamps RH relative humidity S/N serial number µA microamps µs microsecond V volts W watts x
Page 1 and 2: 2832-C Dual-Channel Power Meter OPE
Page 3 and 4: Warranty Newport Corporation warran
Page 5 and 6: Table of Contents Warranty ........
Page 7 and 8: Section 6 - Maintenance, Test and T
Page 9: List of Tables Table 1. Model 2832-
Page 13 and 14: Electrical Specifications: DC Curre
Page 15 and 16: xiv
Page 17 and 18: The Model 2832-C connects to detect
Page 19 and 20: Section 2 System Operation 2.1 Intr
Page 21 and 22: (LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24: When the DIG display annunciator is
Page 25 and 26: Press the , arrow keys to increase
Page 27 and 28: 2.3.18 MENU The MENU key provides a
Page 29 and 30: Table 6 - Menu Level Key Functions
Page 31 and 32: 2.4.3 Meter Configuration The Model
Page 33 and 34: 2.4.5 Attenuator The Attenuator sel
Page 35 and 36: Table 13 - TRIGGER OUT Operations.
Page 37 and 38: 2.5 Connecting AC Power Model 2832-
Page 39 and 40: 2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49 and 50: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 51 and 52: Table 22 - Device Dependent Command
Page 53 and 54: 5.2 Device Independent Commands *CA
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57 and 58: *OPC Signal When Operation Complete
Page 59 and 60: *RCL Recall Meter Configuration Syn
Page 61 and 62:
*STB? Status Byte Query Syntax: *ST
Page 63 and 64:
5.3 Device Dependent Commands ATTN_
Page 65 and 66:
BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68:
DISP Display Brightness Syntax: DIS
Page 69 and 70:
DSBUF_n Data Store Buffer Behavior
Page 71 and 72:
DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74:
Returns: is an integer in the ran
Page 75 and 76:
FILTER_n Filter Select Syntax: FILT
Page 77 and 78:
LLO? Local Lockout Enable Query Syn
Page 79 and 80:
RANGE_n Signal Range Select Syntax:
Page 81 and 82:
RUN_n Start Single Channel Acquisit
Page 83 and 84:
SFREQ? DC Sample Frequency Query Sy
Page 85 and 86:
STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88:
STOREF_n? Store Reference Reading Q
Page 89 and 90:
TRIGOUTLVL Trigger Out Level Select
Page 91 and 92:
USRCAL_n User Calibration Enable Sy
Page 93 and 94:
ZERO_n Signal Zeroing Enable Syntax
Page 95 and 96:
6.3 Troubleshooting Guide The follo
Page 97 and 98:
Section 7 Factory Service 7.1 Intro
Page 100 and 101:
Appendix A Syntax and Definitions A
Page 102 and 103:
A floating point number is defined
Page 104 and 105:
Appendix B Error Messages The IEEE
Page 106 and 107:
-286, “Configuration not compatib
Page 108 and 109:
C.2 Device Event Register The Devic
Page 110 and 111:
C.4 Status Byte The Status Byte reg
Page 112 and 113:
Appendix D Sample Programs D.1 Exam
Page 114 and 115:
D.2 Example Program IEEE-488 Commun
Page 116 and 117:
101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

Create successful ePaper yourself

Delete template?

Save as template?