(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

USRREF_n? User Defined Reference Value Query Syntax: USRREF_n? where n is either A or B Parameters: None Function: This query returns the user defined reference value. This value will be in Watts. Returns: is of type in exponential notation. Related Commands: REFSEL_n, REFSEL_n?, STOREF_n, USRREF_n USRRESP_n User Responsivity Factor Select Syntax: USRRESP_n where n is either A or B Parameters: The parameter is of type . The units of this parameter match the responsivity units of the detector in use. Function: This command is used to define a responsivity factor that will be used by the 2832-C in measurement calculation when user calibration is enabled. Related Commands: ATTN_n, ATTN_n?, LAMBDA_n, LAMBDA_n?, RESP_n?, USRCAL_n, USRCAL_n?, USRRESP_n? USRRESP_n? User Responsivity Factor Query Syntax: USRRESP_n? where n is either A or B Parameters: None Function: This query returns the user defined responsivity factor that will be used by the 2832-C in measurement calculation when user calibration is enabled. Returns: is of type and represents a floating point number. The units of match the responsivity units of detector in use. Related Commands: ATTN_n, ATTN_n?, LAMBDA_n, LAMBDA_n?, RESP_n?, USRCAL_n, USRCAL_n?, USRRESP_n 77
ZERO_n Signal Zeroing Enable Syntax: ZERO_n where n is either A or B Parameters: The parameter is a which can be 0 or 1. If the number is 0, then readings are not adjusted by the stored zero reference. If the number is 1, then readings are adjusted by the stored zero reference. Function: This command enables or disables the zeroing feature. Zeroing causes the stored zero reference (see STOZERO_n command) to be subtracted from incoming signal readings before the incoming signal is used in measurement calculations. Related Commands: STOZERO_n, ZERO_n?, ZEROVAL_n ZERO_n? Signal Zeroing Enable Query Syntax: ZERO_n? where n is either A or B Parameters: None Function: This query returns a value showing whether or not zeroing is enabled or disabled. Returns: is of type and represents the integer 0, if zeroing is enabled, or 1, if zeroing is disabled. Related Commands: STOZERO_n, ZERO_n, ZEROVAL_n ZEROVAL_n? Zero Signal Query Syntax: ZEROVAL_n? where n is either A or B Parameters: None Function: This query returns the current value being used for zeroing. Returns: is of type in exponential notation. The units of this value are the numerator of the detector’s responsivity, i.e. amps. Related Commands: STOZERO_n, ZERO_n, ZERO_n? 78
Page 1 and 2:
2832-C Dual-Channel Power Meter OPE
Page 3 and 4:
Warranty Newport Corporation warran
Page 5 and 6:
Table of Contents Warranty ........
Page 7 and 8:
Section 6 - Maintenance, Test and T
Page 9 and 10:
List of Tables Table 1. Model 2832-
Page 11 and 12:
Definitions A amps AC alternating c
Page 13 and 14:
Electrical Specifications: DC Curre
Page 15 and 16:
xiv
Page 17 and 18:
The Model 2832-C connects to detect
Page 19 and 20:
Section 2 System Operation 2.1 Intr
Page 21 and 22:
(LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24:
When the DIG display annunciator is
Page 25 and 26:
Press the , arrow keys to increase
Page 27 and 28:
2.3.18 MENU The MENU key provides a
Page 29 and 30:
Table 6 - Menu Level Key Functions
Page 31 and 32:
2.4.3 Meter Configuration The Model
Page 33 and 34:
2.4.5 Attenuator The Attenuator sel
Page 35 and 36:
Table 13 - TRIGGER OUT Operations.
Page 37 and 38:
2.5 Connecting AC Power Model 2832-
Page 39 and 40:
2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49 and 50: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 51 and 52: Table 22 - Device Dependent Command
Page 53 and 54: 5.2 Device Independent Commands *CA
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57 and 58: *OPC Signal When Operation Complete
Page 59 and 60: *RCL Recall Meter Configuration Syn
Page 61 and 62: *STB? Status Byte Query Syntax: *ST
Page 63 and 64: 5.3 Device Dependent Commands ATTN_
Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68: DISP Display Brightness Syntax: DIS
Page 69 and 70: DSBUF_n Data Store Buffer Behavior
Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74: Returns: is an integer in the ran
Page 75 and 76: FILTER_n Filter Select Syntax: FILT
Page 77 and 78: LLO? Local Lockout Enable Query Syn
Page 79 and 80: RANGE_n Signal Range Select Syntax:
Page 81 and 82: RUN_n Start Single Channel Acquisit
Page 83 and 84: SFREQ? DC Sample Frequency Query Sy
Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88: STOREF_n? Store Reference Reading Q
Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
Page 91: USRCAL_n User Calibration Enable Sy
Page 95 and 96: 6.3 Troubleshooting Guide The follo
Page 97 and 98: Section 7 Factory Service 7.1 Intro
Page 100 and 101: Appendix A Syntax and Definitions A
Page 102 and 103: A floating point number is defined
Page 104 and 105: Appendix B Error Messages The IEEE
Page 106 and 107: -286, “Configuration not compatib
Page 108 and 109: C.2 Device Event Register The Devic
Page 110 and 111: C.4 Status Byte The Status Byte reg
Page 112 and 113: Appendix D Sample Programs D.1 Exam
Page 114 and 115: D.2 Example Program IEEE-488 Commun
Page 116 and 117: 101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?