(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

*PRE Parallel Poll Enable Syntax: *PRE Parameters: is an integer in the range 0 to 255 inclusive. The value of this number is written into the Parallel Poll Enable register. Function: This command sets the Parallel Poll Enable register bits. The Parallel Poll Enable register is used in conjunction with the Status Byte to generate the IST (Individual Status) message. See Appendix C for a detailed description of the Event Status Register. The Parallel Poll Enable Register is set to 0 at power-on. The Parallel Poll Enable Register is an 8-bit, bit mapped register, with each bit signifying a different condition. The bits and their significance are detailed below: 7 6 5 4 3 2 1 0 New Data Available New Valid Data Available Not Used Not Used Message Available Mask Event Status Byte Mask Master Summary Status Mask Error Queue Mask Parallel Poll Enable Register Related Commands: *IST, *PRE?, *STB?*PRE? *PRE? Parallel Poll Enable Query Syntax: *PRE? Parameters: None Function: This query returns the contents of the Parallel Poll Enable register. See the *PRE command for a description of the Parallel Poll Enable register. See Appendix C for a detailed description of the Event Status Register. Returns: is of type and represents an unsigned integer in the range 0 to 255. Related Commands: *IST, *PRE, *STB? 43
*RCL Recall Meter Configuration Syntax: *RCL Parameters: is of type which rounds to an integer in the range 0 to 9. This number specifies a configuration storage buffer. The number 0 stands for the default configuration buffer. Function: This command configures the meter to a configuration previously stored in non-volatile memory (see *SAV), or to the default configuration for the attached detector. This command will fail if the requested configuration is incompatible with the detector attached to the meter or empty. The parameters affected by this command are those listed in Table 8. Returns: None Related Commands: *RST, *SAV *RST Reset Syntax: *RST Parameters: None Function: This sets the meter to the default configuration, see Table 8, for the detector attached to it. It also cancels any outstanding *OPC or *OPC? commands. Related Commands: *RCL, *SAV *SAV Save Meter Configuration Syntax: *SAV Parameters: is of type which rounds to an integer in the range 1 to 9. This number specifies a configuration storage buffer. Function: This command saves the configuration of the meter to the configuration specified by the parameter. The parameters saved by this command are those listed in Table 8. Related Commands: *RCL, *RST 44
Page 1 and 2:
2832-C Dual-Channel Power Meter OPE
Page 3 and 4:
Warranty Newport Corporation warran
Page 5 and 6:
Table of Contents Warranty ........
Page 7 and 8: Section 6 - Maintenance, Test and T
Page 9 and 10: List of Tables Table 1. Model 2832-
Page 11 and 12: Definitions A amps AC alternating c
Page 13 and 14: Electrical Specifications: DC Curre
Page 15 and 16: xiv
Page 17 and 18: The Model 2832-C connects to detect
Page 19 and 20: Section 2 System Operation 2.1 Intr
Page 21 and 22: (LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24: When the DIG display annunciator is
Page 25 and 26: Press the , arrow keys to increase
Page 27 and 28: 2.3.18 MENU The MENU key provides a
Page 29 and 30: Table 6 - Menu Level Key Functions
Page 31 and 32: 2.4.3 Meter Configuration The Model
Page 33 and 34: 2.4.5 Attenuator The Attenuator sel
Page 35 and 36: Table 13 - TRIGGER OUT Operations.
Page 37 and 38: 2.5 Connecting AC Power Model 2832-
Page 39 and 40: 2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49 and 50: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 51 and 52: Table 22 - Device Dependent Command
Page 53 and 54: 5.2 Device Independent Commands *CA
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57: *OPC Signal When Operation Complete
Page 61 and 62: *STB? Status Byte Query Syntax: *ST
Page 63 and 64: 5.3 Device Dependent Commands ATTN_
Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68: DISP Display Brightness Syntax: DIS
Page 69 and 70: DSBUF_n Data Store Buffer Behavior
Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74: Returns: is an integer in the ran
Page 75 and 76: FILTER_n Filter Select Syntax: FILT
Page 77 and 78: LLO? Local Lockout Enable Query Syn
Page 79 and 80: RANGE_n Signal Range Select Syntax:
Page 81 and 82: RUN_n Start Single Channel Acquisit
Page 83 and 84: SFREQ? DC Sample Frequency Query Sy
Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88: STOREF_n? Store Reference Reading Q
Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
Page 91 and 92: USRCAL_n User Calibration Enable Sy
Page 93 and 94: ZERO_n Signal Zeroing Enable Syntax
Page 95 and 96: 6.3 Troubleshooting Guide The follo
Page 97 and 98: Section 7 Factory Service 7.1 Intro
Page 100 and 101: Appendix A Syntax and Definitions A
Page 102 and 103: A floating point number is defined
Page 104 and 105: Appendix B Error Messages The IEEE
Page 106 and 107: -286, “Configuration not compatib
Page 108 and 109:
C.2 Device Event Register The Devic
Page 110 and 111:
C.4 Status Byte The Status Byte reg
Page 112 and 113:
Appendix D Sample Programs D.1 Exam
Page 114 and 115:
D.2 Example Program IEEE-488 Commun
Page 116 and 117:
101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?