(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

Command RANGE_n? REFSEL_n REFSEL_n? RESP_n? RUN RUN_n RWS? RWS_n? SFREQ SFREQ? SPREC SPREC? STMAX_n? STMEAN_n? STMIN_n? STMXMN_n? STSDEV_n? STSIZE_n STSIZE_n? STOP STOP_n STOREF_n STOREF_n? STOZERO_n TRIGOUT TRIGOUT? TRIGOUTFREQ TRIGOUTFREQ? TRIGOUTLVL TRIGOUTLVL? TRIGOUTPOL TRIGOUTPOL? UNITS_n UNITS_n? USRCAL_n USRCAL_n? USRREF_n USRREF_n? USRRESP_n USRRESP_n? ZERO_n ZERO_n? ZEROVAL_n? Command Name <strong>Manual</strong> Range Level Query Reference Source Select Reference Source Query Responsivity Query Start Both Channel Acquisition Start Single Channel Acquisition Read Both Channel Measurements with Status Query Read Single Measurement with Status Query DC Sample Frequency Select DC Sample Frequency Query DC Sample Type Select DC Sample Type Query Statistics Buffer Maximum Value Query Statistics Buffer Mean Value Query Statistics Buffer Minimum Value Query Statistics Buffer Maximum-Minimum Value Query Statistics Buffer Standard Deviation Query Statistics Buffer Size Select Statistics Buffer Size Query Stop Both Channel Acquisition Stop Single Channel Acquisition Store Reference Reading Store Reference Query Reading Store Zero Signal Trigger Out Mode Select Trigger Out Mode Query Trigger Out Frequency Select Trigger Out Frequency Query Trigger Out Level Select Trigger Out Level Query Trigger Out Polarity Select Trigger Out Polarity Query Units Select Units Query User Calibration Enable User Calibration Enable Query User Defined Reference Value Select User Defined Reference Value Query User Responsivity Factor Select User Responsivity Factor Query Signal Zeroing Enable Signal Zeroing Enable Query Zero Signal Query NOTE n stands for A (channel A) or B (channel B). 37
5.2 Device Independent Commands *CAL? Calibration Query Syntax: *CAL? Parameters: None Function: This routine performs an auto calibration sequence on both channels. The calibration sequence measures the amplifier offsets at all gain settings. These measurements are stored and subtracted from subsequent measurements. Acquisition is suspended during auto calibration and no other remote commands will be processed until the auto calibration sequence is complete. Returns: represents the integer 0. This return value is generated when autocalibration is complete. Related Commands: None *CLS Clear Status Syntax: *CLS Parameters: None Function: This command clears the Standard Event Status register, device event register, and the error queue. As a result of this command the status byte is cleared except for the message available bit (bit 4). Because this command does not clear the input and output buffers the MAV bit will not be affected. The *CLS command also cancels any outstanding *OPC and OPC? commands. Related Commands: *ESR?, EVENT?, *IST?, *STB? *ERR? Error Query Syntax: *ERR? Parameters: None Function: Returns (and removes) oldest error message from the error queue. The error message is made up of an error code and a text description of the error (see the Appendix B). A maximum of 10 errors can be stored in the queue. If no 38
Page 1 and 2: 2832-C Dual-Channel Power Meter OPE
Page 3 and 4: Warranty Newport Corporation warran
Page 5 and 6: Table of Contents Warranty ........
Page 7 and 8: Section 6 - Maintenance, Test and T
Page 9 and 10: List of Tables Table 1. Model 2832-
Page 11 and 12: Definitions A amps AC alternating c
Page 13 and 14: Electrical Specifications: DC Curre
Page 15 and 16: xiv
Page 17 and 18: The Model 2832-C connects to detect
Page 19 and 20: Section 2 System Operation 2.1 Intr
Page 21 and 22: (LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24: When the DIG display annunciator is
Page 25 and 26: Press the , arrow keys to increase
Page 27 and 28: 2.3.18 MENU The MENU key provides a
Page 29 and 30: Table 6 - Menu Level Key Functions
Page 31 and 32: 2.4.3 Meter Configuration The Model
Page 33 and 34: 2.4.5 Attenuator The Attenuator sel
Page 35 and 36: Table 13 - TRIGGER OUT Operations.
Page 37 and 38: 2.5 Connecting AC Power Model 2832-
Page 39 and 40: 2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49 and 50: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 51: Table 22 - Device Dependent Command
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57 and 58: *OPC Signal When Operation Complete
Page 59 and 60: *RCL Recall Meter Configuration Syn
Page 61 and 62: *STB? Status Byte Query Syntax: *ST
Page 63 and 64: 5.3 Device Dependent Commands ATTN_
Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68: DISP Display Brightness Syntax: DIS
Page 69 and 70: DSBUF_n Data Store Buffer Behavior
Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74: Returns: is an integer in the ran
Page 75 and 76: FILTER_n Filter Select Syntax: FILT
Page 77 and 78: LLO? Local Lockout Enable Query Syn
Page 79 and 80: RANGE_n Signal Range Select Syntax:
Page 81 and 82: RUN_n Start Single Channel Acquisit
Page 83 and 84: SFREQ? DC Sample Frequency Query Sy
Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88: STOREF_n? Store Reference Reading Q
Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
Page 91 and 92: USRCAL_n User Calibration Enable Sy
Page 93 and 94: ZERO_n Signal Zeroing Enable Syntax
Page 95 and 96: 6.3 Troubleshooting Guide The follo
Page 97 and 98: Section 7 Factory Service 7.1 Intro
Page 100 and 101: Appendix A Syntax and Definitions A
Page 102 and 103:
A floating point number is defined
Page 104 and 105:
Appendix B Error Messages The IEEE
Page 106 and 107:
-286, “Configuration not compatib
Page 108 and 109:
C.2 Device Event Register The Devic
Page 110 and 111:
C.4 Status Byte The Status Byte reg
Page 112 and 113:
Appendix D Sample Programs D.1 Exam
Page 114 and 115:
D.2 Example Program IEEE-488 Commun
Page 116 and 117:
101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?