(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

RWS_n? Read Single Channel Measurement With Status Query Syntax: RWS_n? Parameters: None Function: This query returns the last measurement taken from the specified channel. The units of this measurement are the units defined at the time the reading was made. Because it is possible to make this query faster than measurements are actually being taken, the values returned by successive queries may be multiple reports of the same measurement. To ensure that fresh data is being read the NDA(new data available) bit in the Status Byte can be checked either by issuing a serial poll or by using the *STB? command. A serial poll is recommended if the GPIB interface is being used. The NDA bit will be 1 if the last measurement has not been read. The NDA bit for the specified channel will be reset to 0 immediately after a measurement is queried from that channel and will stay 0 until a new reading is taken. Returns: , is an integer that represents the status of the returned value. will be 0 for ok, 1 for over range, 2 for saturated and 3 for data error, and 4 for ranging. is a floating point number in the exponential format. Related Commands: *STB?, MODE_n, MODE_n?, R?, R_n?, RWS? UNITS_n, UNITS_n? SFREQ DC Sample Frequency Select Syntax: SFREQ Parameters: The parameter is of type . The range of this number depends on the current DC sample precision (see SPREC). If the precision is 20000 then the range is 0.001 to 25Hz. If the precision is 4096 then the range is 0.001 to 500Hz when two detector calibration modules are plugged into the meter and 1000Hz for one. Function: This command determines how often a signal is sampled when in DC continuous mode. Both channels sample data at the same rate when in DC continuous mode. Related Commands: SFREQ?, SPREC, SPREC? 67
SFREQ? DC Sample Frequency Query Syntax: SFREQ? Parameters: None Function: This query returns the sample rate used for continuous DC acquisition on both channels Returns: is of type in exponent notation with units of hertz or samples per second. Related Commands: SFREQ, SPREC, SPREC? SPREC DC Sample Precision Select Syntax: SPREC Parameters: The parameter is of type with acceptable values of 20000 or 4096. Function: The 2832-C has a 20,000 count high precision A/D and a 4,096 count A/D. This command determines which of these A/Ds will be used from both channels to acquire samples during DC single and DC continuous acquisition modes. This command affects the available range of DC sample frequencies. Note that the 4,096 count A/D is used during all other acquisition modes. Related Commands: SFREQ, SFREQ?, SPREC? SPREC? DC Sample Precision Query Syntax: SPREC? Parameters: None Function: This query returns a string that indicates whether the 20,000 count A/D or the 4,096 count A/D will be used during DC CONT or DC SNGL acquisition modes on both channels. Returns: is of type . It will be 20000 if the 20,000 count A/D is selected and 4096 if the 4,096 count A/D is selected. Related Commands: SFREQ, SFREQ?, SPREC? 68
Page 1 and 2:
2832-C Dual-Channel Power Meter OPE
Page 3 and 4:
Warranty Newport Corporation warran
Page 5 and 6:
Table of Contents Warranty ........
Page 7 and 8:
Section 6 - Maintenance, Test and T
Page 9 and 10:
List of Tables Table 1. Model 2832-
Page 11 and 12:
Definitions A amps AC alternating c
Page 13 and 14:
Electrical Specifications: DC Curre
Page 15 and 16:
xiv
Page 17 and 18:
The Model 2832-C connects to detect
Page 19 and 20:
Section 2 System Operation 2.1 Intr
Page 21 and 22:
(LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24:
When the DIG display annunciator is
Page 25 and 26:
Press the , arrow keys to increase
Page 27 and 28:
2.3.18 MENU The MENU key provides a
Page 29 and 30:
Table 6 - Menu Level Key Functions
Page 31 and 32: 2.4.3 Meter Configuration The Model
Page 33 and 34: 2.4.5 Attenuator The Attenuator sel
Page 35 and 36: Table 13 - TRIGGER OUT Operations.
Page 37 and 38: 2.5 Connecting AC Power Model 2832-
Page 39 and 40: 2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49 and 50: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 51 and 52: Table 22 - Device Dependent Command
Page 53 and 54: 5.2 Device Independent Commands *CA
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57 and 58: *OPC Signal When Operation Complete
Page 59 and 60: *RCL Recall Meter Configuration Syn
Page 61 and 62: *STB? Status Byte Query Syntax: *ST
Page 63 and 64: 5.3 Device Dependent Commands ATTN_
Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68: DISP Display Brightness Syntax: DIS
Page 69 and 70: DSBUF_n Data Store Buffer Behavior
Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74: Returns: is an integer in the ran
Page 75 and 76: FILTER_n Filter Select Syntax: FILT
Page 77 and 78: LLO? Local Lockout Enable Query Syn
Page 79 and 80: RANGE_n Signal Range Select Syntax:
Page 81: RUN_n Start Single Channel Acquisit
Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88: STOREF_n? Store Reference Reading Q
Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
Page 91 and 92: USRCAL_n User Calibration Enable Sy
Page 93 and 94: ZERO_n Signal Zeroing Enable Syntax
Page 95 and 96: 6.3 Troubleshooting Guide The follo
Page 97 and 98: Section 7 Factory Service 7.1 Intro
Page 100 and 101: Appendix A Syntax and Definitions A
Page 102 and 103: A floating point number is defined
Page 104 and 105: Appendix B Error Messages The IEEE
Page 106 and 107: -286, “Configuration not compatib
Page 108 and 109: C.2 Device Event Register The Devic
Page 110 and 111: C.4 Status Byte The Status Byte reg
Page 112 and 113: Appendix D Sample Programs D.1 Exam
Page 114 and 115: D.2 Example Program IEEE-488 Commun
Page 116 and 117: 101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?