- Page 1 and 2:
2832-C Dual-Channel Power Meter OPE
- Page 3 and 4:
Warranty Newport Corporation warran
- Page 5 and 6:
Table of Contents Warranty ........
- Page 7 and 8:
Section 6 - Maintenance, Test and T
- Page 9 and 10:
List of Tables Table 1. Model 2832-
- Page 11 and 12:
Definitions A amps AC alternating c
- Page 13 and 14:
Electrical Specifications: DC Curre
- Page 15 and 16:
xiv
- Page 17 and 18:
The Model 2832-C connects to detect
- Page 19 and 20:
Section 2 System Operation 2.1 Intr
- Page 21 and 22:
(LOCAL) SHIFT STO REF DISP REF SEL
- Page 23 and 24:
When the DIG display annunciator is
- Page 25 and 26:
Press the , arrow keys to increase
- Page 27 and 28:
2.3.18 MENU The MENU key provides a
- Page 29 and 30:
Table 6 - Menu Level Key Functions
- Page 31 and 32:
2.4.3 Meter Configuration The Model
- Page 33 and 34:
2.4.5 Attenuator The Attenuator sel
- Page 35 and 36:
Table 13 - TRIGGER OUT Operations.
- Page 37 and 38:
2.5 Connecting AC Power Model 2832-
- Page 39 and 40:
2.7 Power Up Turn on the Model 2832
- Page 41 and 42:
3.3 Digitized Signal Flow Signals t
- Page 43 and 44:
3.6 Measurement Considerations This
- Page 45 and 46:
Section 4 Computer Interfacing 4.1
- Page 47 and 48:
4.3 Entering Remote Computer Interf
- Page 49 and 50:
4.5 RS-232C XON/XOFF Handshaking Pr
- Page 51 and 52:
Table 22 - Device Dependent Command
- Page 53 and 54:
5.2 Device Independent Commands *CA
- Page 55 and 56:
*ESE? Event Status Enable Query Syn
- Page 57 and 58:
*OPC Signal When Operation Complete
- Page 59 and 60:
*RCL Recall Meter Configuration Syn
- Page 61 and 62:
*STB? Status Byte Query Syntax: *ST
- Page 63 and 64:
5.3 Device Dependent Commands ATTN_
- Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
- Page 67 and 68: DISP Display Brightness Syntax: DIS
- Page 69 and 70: DSBUF_n Data Store Buffer Behavior
- Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
- Page 73 and 74: Returns: is an integer in the ran
- Page 75 and 76: FILTER_n Filter Select Syntax: FILT
- Page 77 and 78: LLO? Local Lockout Enable Query Syn
- Page 79 and 80: RANGE_n Signal Range Select Syntax:
- Page 81 and 82: RUN_n Start Single Channel Acquisit
- Page 83 and 84: SFREQ? DC Sample Frequency Query Sy
- Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
- Page 87 and 88: STOREF_n? Store Reference Reading Q
- Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
- Page 91 and 92: USRCAL_n User Calibration Enable Sy
- Page 93 and 94: ZERO_n Signal Zeroing Enable Syntax
- Page 95 and 96: 6.3 Troubleshooting Guide The follo
- Page 97 and 98: Section 7 Factory Service 7.1 Intro
- Page 100 and 101: Appendix A Syntax and Definitions A
- Page 102 and 103: A floating point number is defined
- Page 104 and 105: Appendix B Error Messages The IEEE
- Page 106 and 107: -286, “Configuration not compatib
- Page 108 and 109: C.2 Device Event Register The Devic
- Page 110 and 111: C.4 Status Byte The Status Byte reg
- Page 112 and 113: Appendix D Sample Programs D.1 Exam
- Page 114 and 115: D.2 Example Program IEEE-488 Commun