(8.5x11) 6000 Manual Cover - Newport Corporation

More documents

Recommendations

Info

Section 5 Command Reference 5.1 Model 2832-C Remote Interface Commands The Model 2832-C remote commands can be divided into two groupings: i. Device Independent Commands, Section 5.2 ii. Device Dependent Commands, Section 5.3 Table 21 lists the Device Independent Commands supported by the 2832-C while Table 22 lists the Device Dependent Commands supported the 2832-C. Following these tables are the detailed presentations of each command and its syntax and an example of its use. Command *CAL? *CLS *ERR? *ESE *ESE? *ESR? *IDN? *IST? *OPC *OPC? *PRE *PRE? *RCL *RST *SAV *SRE *SRE? *STB? *TST? *WAI Table 21 – Device Independent Status Commands Command Name Calibration Query Clear Status Error Query Event Status Enable Event Status Enable Query Event Status Register Query Identification Query Individual Status Query Signal When Operation Complete Operation Complete Query Parallel Poll Enable Parallel Poll Enable Query Recall Device Configuration Software Reset Save Device Configuration Service Request Enable Service Request Enable Query Status Byte System Test Wait To Continue 35
Table 22 – Device Dependent Commands Command Command Name ATTN_n Attenuator Calibration Data Enable ATTN_n? Attenuator Calibration Data Enable Query ATTNSN_n? Attenuator Serial Number Query AUTO_n Auto Ranging Enable AUTO_n? Auto Ranging Enable Query BARGRAPH Bar Graph Enable BARGRAPH? Bar Graph Enable Query CALDATE_n? Calibration Date Query CH? Available Channel Query DETMODEL_n? Detector Mode Query DETSN_n? Detector Serial Number Query DISP Display Brightness Select DISP? Display Brightness Query DISPCH Display Channel Select DISPCH? Display Channel Query DS_n? Data Store Value Query DSBUF_n Data Store Buffer Behavior Select DSBUF_n? Data Store Buffer Behavior Query DSCLR_n Data Store Clear DSCNT_n? Data Store Value Count Query DSE_n Data Store Enable DSE_n? Data Store Enable Query DSSIZE_n Data Store Buffer Size Select DSSIZE_n? Data Store Buffer Size Query DSUNITS_n? Data Store Units Query ECHO RS-232 Echo Mode Enable ECHO? RS-232 Echo Mode Enable Query EVENT? Device Event Register Query EVENTEN Device Event Enable Register EVENTEN? Device Event Enable Register Query EXT External Trigger Enable EXT? External Trigger Enable Query EXTEDGE External Trigger Edge Select EXTEDGE? External Trigger Edge Query FILTER_n Filter Select FILTER_n? Filter Query LAMBDA_n Lambda Select LAMBDA_n? Lambda Query LLO Local Lockout Enable LLO? Local Lockout Enable Query MODE_n Acquisition Mode Select MODE_n? Acquisition Mode Query R? Read Both Channel Measurements Query R_n? Read Single Channel Measurement Query RANGE_n <strong>Manual</strong> Range Level Select 36
Page 1 and 2: 2832-C Dual-Channel Power Meter OPE
Page 3 and 4: Warranty Newport Corporation warran
Page 5 and 6: Table of Contents Warranty ........
Page 7 and 8: Section 6 - Maintenance, Test and T
Page 9 and 10: List of Tables Table 1. Model 2832-
Page 11 and 12: Definitions A amps AC alternating c
Page 13 and 14: Electrical Specifications: DC Curre
Page 15 and 16: xiv
Page 17 and 18: The Model 2832-C connects to detect
Page 19 and 20: Section 2 System Operation 2.1 Intr
Page 21 and 22: (LOCAL) SHIFT STO REF DISP REF SEL
Page 23 and 24: When the DIG display annunciator is
Page 25 and 26: Press the , arrow keys to increase
Page 27 and 28: 2.3.18 MENU The MENU key provides a
Page 29 and 30: Table 6 - Menu Level Key Functions
Page 31 and 32: 2.4.3 Meter Configuration The Model
Page 33 and 34: 2.4.5 Attenuator The Attenuator sel
Page 35 and 36: Table 13 - TRIGGER OUT Operations.
Page 37 and 38: 2.5 Connecting AC Power Model 2832-
Page 39 and 40: 2.7 Power Up Turn on the Model 2832
Page 41 and 42: 3.3 Digitized Signal Flow Signals t
Page 43 and 44: 3.6 Measurement Considerations This
Page 45 and 46: Section 4 Computer Interfacing 4.1
Page 47 and 48: 4.3 Entering Remote Computer Interf
Page 49: 4.5 RS-232C XON/XOFF Handshaking Pr
Page 53 and 54: 5.2 Device Independent Commands *CA
Page 55 and 56: *ESE? Event Status Enable Query Syn
Page 57 and 58: *OPC Signal When Operation Complete
Page 59 and 60: *RCL Recall Meter Configuration Syn
Page 61 and 62: *STB? Status Byte Query Syntax: *ST
Page 63 and 64: 5.3 Device Dependent Commands ATTN_
Page 65 and 66: BARGRAPH Bar Graph Enable Syntax: B
Page 67 and 68: DISP Display Brightness Syntax: DIS
Page 69 and 70: DSBUF_n Data Store Buffer Behavior
Page 71 and 72: DSSIZE_n Data Store Buffer Size Sel
Page 73 and 74: Returns: is an integer in the ran
Page 75 and 76: FILTER_n Filter Select Syntax: FILT
Page 77 and 78: LLO? Local Lockout Enable Query Syn
Page 79 and 80: RANGE_n Signal Range Select Syntax:
Page 81 and 82: RUN_n Start Single Channel Acquisit
Page 83 and 84: SFREQ? DC Sample Frequency Query Sy
Page 85 and 86: STMXMN_n? Statistics Buffer Max-Min
Page 87 and 88: STOREF_n? Store Reference Reading Q
Page 89 and 90: TRIGOUTLVL Trigger Out Level Select
Page 91 and 92: USRCAL_n User Calibration Enable Sy
Page 93 and 94: ZERO_n Signal Zeroing Enable Syntax
Page 95 and 96: 6.3 Troubleshooting Guide The follo
Page 97 and 98: Section 7 Factory Service 7.1 Intro
Page 100 and 101:
Appendix A Syntax and Definitions A
Page 102 and 103:
A floating point number is defined
Page 104 and 105:
Appendix B Error Messages The IEEE
Page 106 and 107:
-286, “Configuration not compatib
Page 108 and 109:
C.2 Device Event Register The Devic
Page 110 and 111:
C.4 Status Byte The Status Byte reg
Page 112 and 113:
Appendix D Sample Programs D.1 Exam
Page 114 and 115:
D.2 Example Program IEEE-488 Commun
Page 116 and 117:
101
show all

(8.5x11) 6000 Manual Cover - Newport Corporation

Create successful ePaper yourself

Delete template?

Save as template?