AS-3640

More documents

Recommendations

Info

Pos: 101.4 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Error Messages/04_ERROR_PAPER_SENSOR @ 2\mod_1265617418639_912.doc @ 11281 @ Pos 101.5 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Error Messages/05_Increase_The_Gap! @ 2\mod_1265617469330_912.doc @ 11284 @ Protocol code Display message Cause 003 PAPER TOO SMALL OR WRONG PAPER WIDTH! CODE: 03 Elimination • Measure actual paper size • Compare paper size in transport direction with size set in printer • Compare paper size in PC software with size set in printer • Check if a wrong paper size is locked • When using material with nonrectangular edges or with press cut sections turn off the PAPER SENSOR in the menu • Attach a holding-down device when using uneven materials (e.g. foil-wrapped magazines) • Adjust/teach-in paper sensor • Check paper sensor in HARDWARE TEST Expected paper size too small Fixed Head Printer with one print unit: • If your material is preprinted on the reverse side set the PAPER SENSOR to Off and blank colourpaper. Fixed Head Printer with more than one print unit: • Clean the reflector of the paper sensor • Check that the reflector is aligned parallel to the paper sensor • Check if the reflector is damaged Printer with separate feeder: • Check if paper gets stuck on any machine parts • Check if the paper enters the printer parallel aligned • Check paper sensor cable • Check if the belt(s) is running in the correct position Protocol code Display message Cause 004 ERROR PAPER SENSOR CHECK THE SENSOR! Unexpected paper sensor signal CODE: 04 Elimination • Clean the paper sensor • Clean the reflector • Adjust/teach-in paper sensor • Check paper sensor in HARDWARE TEST • Call service 136 User Manual Version 3.1
Pos: 101.6 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Error Messages/06_Reduce_Paper_Speed! @ 2\mod_1265617538818_912.doc @ 11287 @ Pos: 101.7 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Error Messages/07_NO_FEEDER_CABLE_OR_PAPER_ON_THE_BELT @ 2\mod_1265617606807_912.doc @ 11290 @ Pos: 101.8 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Error Messages/09_PRINTING_ERROR_REPEAT_LAST_ADDRESS @ 2\mod_1265617707328_912.doc @ 11296 @ Protocol code Display message Cause 005 INCREASE THE GAP! Ok TO CONTINUE! CODE: 05 Elimination • Check separation system • Check if the feeding components are worn Gap between two products is too small or malfunction of paper sensor Printer with separate feeder: • Decrease the speed of the feeding system Protocol code Display message Cause 006 REDUCE PAPER SPEED! Ok TO CONTINUE! Feeding speed and print data transfer do not match Elimination CODE: 06 Printer with separate feeder: • Decrease the speed of the feeding system • Connect the feeder to the according interface on the printer • Set FEEDER CTRL. MODE to limit overspeed. • Reduce the amount of print data (see chapter X) Protocol code Display message Cause 007 NO FEEDER CABLE OR PAPER ON THE BELT! CODE: 07 Elimination • Connect the feeder to the according interface on the printer The printer detects paper before releasing the feeder output or starting the belt • Remove any paper from the transport belt before starting the print job Protocol code Display message Cause 009 PRINTING ERROR REPEAT LAST ADDRESS. Printer internal error detected CODE: 09 Elimination • Check if the last printed pages were printed correctly • Reprint any faulty pages using the REPEAT PAGES feature from the Quick menu User Manual Version 3.1 137
Page 1 and 2:
AS-3640 ADRESS PRINTER User Manual
Page 3 and 4:
Pos: 3 /[Allgemeines]/0.0a_Note_Tra
Page 5 and 6:
4.5.5 How to activate the emergency
Page 7 and 8:
Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 9 and 10:
Figure 36: Encoder Pattern ........
Page 11 and 12:
Pos: 8 /Bedienungsanleitungen/Gerä
Page 13 and 14:
Pos: 13 /Bedienungsanleitungen/Ger
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
2: Ink costs and ink range This lin
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
CENTAUR SEARCH ....................
Page 49 and 50:
Pos: 75.3 /Bedienungsanleitungen/Ge
Page 51 and 52:
Pos: 75.7 /Bedienungsanleitungen/Ge
Page 53 and 54:
Pos: 75.15 /Bedienungsanleitungen/G
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Figure 24: Adjustment of encoder ne
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
PRINT MIRRORED When set to on, all
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Relay 1 OUTPUT This feature is used
Page 81 and 82:
Page 83 and 84:
Page 85 and 86: Pos: 75.87 /Bedienungsanleitungen/G
Page 89 and 90: Pos: 75.103 /Bedienungsanleitungen/
Page 103 and 104: n n c1 c2 Figure 40: Pattern A with
Page 109 and 110: Pos: 76.2 /Bedienungsanleitungen/Ge
Page 111 and 112: 2. Connect the PC to the printer
Page 115 and 116: Correct IP address syntax Don’t e
Page 117 and 118: 7.3.2.1 Using a fixed IP address 1.
Page 121 and 122: Pos: 77 /Bedienungsanleitungen/Ger
Page 123 and 124: 8.1.2 How to clean an ink cartridge
Page 135: Pos: 101.3 /Bedienungsanleitungen/G
Page 167 and 168: Pos: 115 /Zubehör/AS-OrbitBase/R20
Page 179 and 180: Pos: 123 /Serviceanleitungen/Gerät
Page 181 and 182: 11.5 How to create a print file Dep
Page 183 and 184: Install the printer driver first Pl
Page 185 and 186: 4 • Enable “Send to printer”
Page 187 and 188:
11.8 How to position the paper sens
Page 189 and 190:
The statical Teach-in mode (TM/TB)
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Narrow media and unused separation
Page 197 and 198:
11.14 Additional display texts Unde
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Decap Time Default configuration Di
Page 205 and 206:
Paper recognition Paper Sensor Pape
Page 207 and 208:
Page 209 and 210:
=== Ende der Liste für Textmarke I
show all

AS-3640

Create successful ePaper yourself

Delete template?

Save as template?