AS-3640

More documents

Recommendations

Info

Pos: 75.29 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü3_1303_ADJUSTMENT STEPS @ 0\mod_1254483974277_912.doc @ 4053 @ Figure 26: Adjusted encoder ADJUSTMENT STEPS Pos: 75.30 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü4_130301_PRINT CORR. PATT._Systeme @ 1\mod_1255700246238_912.doc @ 6673 @ PRINT CORR.PATT. This correction pattern is a test printout which allows the user to detect easily the right correction offset. By pressing the Ok key, the printer asks for the available paper source. After choosing between the options “Feeder” (the feeder will dispense one sheet of paper) or “Manual” (the user has to put on paper manually) the printer will start the test print. This kind of calibration may become necessary since a completely tolerance-free production of a print unit is not possible. Slight deviations due to manufacturing tolerances can be balanced via the software of the control device. Calibration can only be carried out at the installed device and can therefore not be performed by the manufacturer. Figure 27 shows an example of this correction pattern. Each column of the printout represents a possible correction value. The user has to choose the pair of bars that matches best. The number above the chosen column represents the correction value for the unit/cartridge combination of the correspondent row (please note that already entered correction values will not have any effect on this test pattern. The test printout is used as a reference to detect offsets between the units/cartridges). 62 User Manual Version 3.1
Pos: 75.31 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü4_130302_CORR. U1-U2 @ 0\mod_1254842361739_912.doc @ 4645 @ Figure 27: PRINT CORR.PATT. for systems with two print units (6 cartridge positions) To perform this print, all ink cartridges must be inserted in the printer. CORR. U1-U2 To ensure the best possible alignment between the print areas of unit U1 and U2, their relative horizontal print positions can be calibrated. This adjustment becomes necessary if there are small offsets in the vertical lines between two print units. The correction values can be adjusted in a range between +50 and -50. One step = 0.08 mm (1/300’’). Press the Quick and the Test Print (Test Print)keys at the same time to perform a TEST PRINT. Use this test print to adjust the horizontal alignment between the units. Positive values will shift the print start of unit U1 a step to the right (relatively to unit U2), negative values will move it to the left (relatively to unit U2). You can also use the PRINT CORR.PATT. test to analyze the offset between the print units. Figure 28 shows a test print that requires a slight adjustment to the left (decrease correction value). The entered correction values influence the print start of all three inserted cartridges. In case of offsets between single cartridges, please follow the instructions of the following chapters CORR. U1 C1-C2 and CORR. U1 C2-C3. -50, -49, ... 0, ..., +49, +50 Default: 0 User Manual Version 3.1 63
Page 1 and 2:
AS-3640 ADRESS PRINTER User Manual
Page 3 and 4:
Pos: 3 /[Allgemeines]/0.0a_Note_Tra
Page 5 and 6:
4.5.5 How to activate the emergency
Page 7 and 8:
Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 9 and 10:
Figure 36: Encoder Pattern ........
Page 11 and 12: Pos: 8 /Bedienungsanleitungen/Gerä
Page 13 and 14: Pos: 13 /Bedienungsanleitungen/Ger
Page 29 and 30: 2: Ink costs and ink range This lin
Page 47 and 48: CENTAUR SEARCH ....................
Page 49 and 50: Pos: 75.3 /Bedienungsanleitungen/Ge
Page 53 and 54: Pos: 75.15 /Bedienungsanleitungen/G
Page 61: Figure 24: Adjustment of encoder ne
Page 67 and 68: PRINT MIRRORED When set to on, all
Page 79 and 80: Relay 1 OUTPUT This feature is used
Page 89 and 90: Pos: 75.103 /Bedienungsanleitungen/
Page 103 and 104: n n c1 c2 Figure 40: Pattern A with
Page 111 and 112: 2. Connect the PC to the printer
Page 113 and 114:
Pos: 76.4 /Bedienungsanleitungen/Ge
Page 115 and 116:
Correct IP address syntax Don’t e
Page 117 and 118:
7.3.2.1 Using a fixed IP address 1.
Page 119 and 120:
Pos: 76.7 /Bedienungsanleitungen/Ge
Page 121 and 122:
Pos: 77 /Bedienungsanleitungen/Ger
Page 123 and 124:
8.1.2 How to clean an ink cartridge
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Pos: 101.3 /Bedienungsanleitungen/G
Page 137 and 138:
Page 139 and 140:
Pos: 101.14 /Bedienungsanleitungen/
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Pos: 115 /Zubehör/AS-OrbitBase/R20
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Pos: 123 /Serviceanleitungen/Gerät
Page 181 and 182:
11.5 How to create a print file Dep
Page 183 and 184:
Install the printer driver first Pl
Page 185 and 186:
4 • Enable “Send to printer”
Page 187 and 188:
11.8 How to position the paper sens
Page 189 and 190:
The statical Teach-in mode (TM/TB)
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Narrow media and unused separation
Page 197 and 198:
11.14 Additional display texts Unde
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Decap Time Default configuration Di
Page 205 and 206:
Paper recognition Paper Sensor Pape
Page 207 and 208:
Page 209 and 210:
=== Ende der Liste für Textmarke I
show all

AS-3640

Create successful ePaper yourself

Delete template?

Save as template?