AS-3640

More documents

Recommendations

Info

Pos: 75.77 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü3_1804_RELAY2 OUTPUT_<strong>AS</strong>-3060A, 620, Orbit, OrbitB @ 0\mod_1254913755613_912.doc @ 4855 @ on print base SET TIME[s] on serial belt SET TIME[s] on 3rd party belt SET TIME[s] downstream from the printer. on print base Use this setting when the dryer is mounted on the same Neopost Base conveyor as the print unit(s). The dryer will be turned off when a stop of this conveyor is detected by the printer. At SET TIME[s] you can set the duration (in seconds) the dryer remains turned on after the last pages exited the printer. (0 – 60 sec. / Default: 5 seconds) on serial belt Use this setting when the dryer is mounted on a serial connected Neopost conveyor. The dryer will be turned off when a stop of this conveyor is detected by the printer. At SET TIME[s] you can set the duration (in seconds) the dryer remains turned on after the last pages exited the printer. (0 – 60 sec. / Default: 5 seconds) on 3rd party belt Use this setting when the dryer is mounted on a third party conveyor belt which is controlled independently from the printer. At SET TIME[s] you can set the duration (in seconds) the dryer remains turned on after the last pages exited the printer. (0 – 60 sec. / Default: 5 seconds) divert DISTANCE Using a dryer! Review all settings carefully before using a dryer! Never operate a dryer without supervision of an operator! Control option for a diverter placed behind the printer (inline). The distance between paper sensor and device has to be entered (range 0 – 5,000 mm). The width (duration) of the signal pulse is calculated from the transport speed and the material size in transport direction. Any device in-between the printer and the diverter can influence the distance. divert works for devices which are downstream from the printer. Trigger divert The divert function must be triggered from a PC application. Default: feeder control 80 User Manual Version 3.1
Pos: 75.78 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü3_1805_IN 1 INPUT @ 1\mod_1256285352045_912.doc @ 6991 @ Pos: 75.79 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü3_1807_FEEDER CTRL. MODE @ 1\mod_1258988414994_912.doc @ 7603 @ Pos: 75.80 /Bedienungsanleitungen/Geräte spezifisch/Drucker/Menüpunkte Drucker/Ü3/Ü4/Ü3_1808_READ & PRINT @ 0\mod_1254913755972_912.doc @ 4859 @ Relay 2 OUTPUT The functions of Relay 2 can be configured in the same way as Relay 1 OUTPUT. See above. Default: feeder control IN 1 INPUT Can be used to send signals to the printer from external devices. IN 2 INPUT Can be used to send signals to the printer from external devices. FEEDER CTRL. MODE This feature is used to set how a connected feeder is controlled by the printer. Option standard limit overspeed Note The feeder receives start and stop signals on job start, on job end and if the user interrupts the print job (e.g. by pressing the “Cancel” key) or if an error occurs. As standard, in addition to that, if the feeding speed is too high the feeder will be stopped. Default: limit overspeed Setting up the feeding speed with the limit overspeed setting When starting a print job, you should begin with a slow feeder speed setting. Increase the feeder speed until the printer begins to turn the feeder off and on again. Now decrease the speed until the feeder runs continuously without being stopped by the printer due to a too high speed. User Manual Version 3.1 81
Page 1 and 2:
AS-3640 ADRESS PRINTER User Manual
Page 3 and 4:
Pos: 3 /[Allgemeines]/0.0a_Note_Tra
Page 5 and 6:
4.5.5 How to activate the emergency
Page 7 and 8:
Pos: 6 /[Allgemeines]/0.3_Abbildung
Page 9 and 10:
Figure 36: Encoder Pattern ........
Page 11 and 12:
Pos: 8 /Bedienungsanleitungen/Gerä
Page 13 and 14:
Pos: 13 /Bedienungsanleitungen/Ger
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30: 2: Ink costs and ink range This lin
Page 31 and 32: Pos: 48 /Bedienungsanleitungen/Ger
Page 47 and 48: CENTAUR SEARCH ....................
Page 49 and 50: Pos: 75.3 /Bedienungsanleitungen/Ge
Page 53 and 54: Pos: 75.15 /Bedienungsanleitungen/G
Page 61 and 62: Figure 24: Adjustment of encoder ne
Page 67 and 68: PRINT MIRRORED When set to on, all
Page 79: Relay 1 OUTPUT This feature is used
Page 89 and 90: Pos: 75.103 /Bedienungsanleitungen/
Page 103 and 104: n n c1 c2 Figure 40: Pattern A with
Page 111 and 112: 2. Connect the PC to the printer
Page 115 and 116: Correct IP address syntax Don’t e
Page 117 and 118: 7.3.2.1 Using a fixed IP address 1.
Page 123 and 124: 8.1.2 How to clean an ink cartridge
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Pos: 101.3 /Bedienungsanleitungen/G
Page 137 and 138:
Page 139 and 140:
Pos: 101.14 /Bedienungsanleitungen/
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Pos: 115 /Zubehör/AS-OrbitBase/R20
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Pos: 123 /Serviceanleitungen/Gerät
Page 181 and 182:
11.5 How to create a print file Dep
Page 183 and 184:
Install the printer driver first Pl
Page 185 and 186:
4 • Enable “Send to printer”
Page 187 and 188:
11.8 How to position the paper sens
Page 189 and 190:
The statical Teach-in mode (TM/TB)
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Narrow media and unused separation
Page 197 and 198:
11.14 Additional display texts Unde
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Decap Time Default configuration Di
Page 205 and 206:
Paper recognition Paper Sensor Pape
Page 207 and 208:
Page 209 and 210:
=== Ende der Liste für Textmarke I
show all

AS-3640

Create successful ePaper yourself

Delete template?

Save as template?