DE2-115: User Manual

More documents

Recommendations

Info

One 40-pin Expansion Header with diode protection One High Speed Mezzanine Card (HSMC) connector 16x2 LCD module In addition to these hardware features, the DE2-115 board has software support for standard I/O interfaces and a control panel facility for accessing various components. Also, the software is provided for supporting a number of demonstrations that illustrate the advanced capabilities of the DE2-115 board. In order to use the DE2-115 board, the user has to be familiar with the Quartus II software. The necessary knowledge can be acquired by reading the tutorials “Getting Started with Altera’s DE2-115 Board” (tut_initialDE2-115.pdf) and “Quartus II Introduction” (which exists in three versions based on the design entry method used, namely Verilog, VHDL or schematic entry). These tutorials are provided in the directory DE2_115_tutorials on the DE2-115 System CD that accompanies the DE2-115 kit and can also be found on Terasic‟s DE2-115 web pages. 2.2 Block Diagram of the DE2-115 Board Figure 2-3 gives the block diagram of the DE2-115 board. To provide maximum flexibility for the user, all connections are made through the Cyclone IV E FPGA device. Thus, the user can configure the FPGA to implement any system design. Figure 2-3 Block Diagram of DE2-115 9
Following is more detailed information about the blocks in Figure 2-3: FPGA device Cyclone IV EP4CE115F29 device 114,480 LEs 432 M9K memory blocks 3,888 Kbits embedded memory 4 PLLs FPGA configuration JTAG and AS mode configuration EPCS64 serial configuration device On-board USB Blaster circuitry Memory devices 128MB (32Mx32bit) SDRAM 2MB (1Mx16) SRAM 8MB (4Mx16) Flash with 8-bit mode 32Kb EEPROM SD Card socket Provides SPI and 4-bit SD mode for SD Card access Connectors Two Ethernet 10/100/1000 Mbps ports High Speed Mezzanine Card (HSMC) Configurable I/O standards (voltage levels:3.3/2.5/1.8/1.5V) USB type A and B o Provide host and device controllers compliant with USB 2.0 o Support data transfer at full-speed and low-speed o PC driver available 10
Page 2 and 3: CONTENTS Chapter 1 DE2-115 Package
Page 4 and 5: 6.9 IR Receiver Demonstration .....
Page 6 and 7: Bag of six rubber (silicon) covers
Page 8 and 9: Chapter 2 Introduction of the Alter
Page 12 and 13: 40-pin expansion port o Configurabl
Page 14 and 15: You can also connect a microphone t
Page 16 and 17: 5. The DE2_115_ControlPanel.sof bit
Page 18 and 19: Figure 3-3 Controlling LEDs Choosin
Page 20 and 21: Figure 3-6 Monitoring switches and
Page 22 and 23: The Sequential Read function is use
Page 24 and 25: 3.7 SD Card The function is designe
Page 26 and 27: 1. Choosing the VGA tab leads to th
Page 28 and 29: Figure 3-14 Testing the IR receiver
Page 30 and 31: Chapter 4 Using the DE2-115 Board T
Page 32 and 33: • Configuring the FPGA in JTAG Mo
Page 34 and 35: Figure 4-6 Connections between the
Page 36 and 37: Table 4-1 Pin Assignments for Slide
Page 38 and 39: HEX0[5] PIN_J22 Seven Segment Digit
Page 40 and 41: 4.6 Using the LCD Module The LCD mo
Page 42 and 43: Figure 4-13 HSMC VCCIO supply volta
Page 44 and 45: HSMC_RX_D_N[1] PIN_C27 HSMC_RX_D_N[
Page 46 and 47: HSMC_TX_D_N[14] PIN_U28 HSMC_TX_D_N
Page 48 and 49: The voltage level of the I/O pins o
Page 50 and 51: Figure 4-19 Using Emulated LVDS on
Page 52 and 53: 4.10 Using VGA The DE2-115 board in
Page 54 and 55: Table 4-16 Pin Assignments for ADV7
Page 56 and 57: Figure 4-24 Connections between FPG
Page 58 and 59: You will need to perform a hardware
Page 60 and 61:
ENET1_TX_CLK PIN_C22 MII transmit c
Page 62 and 63:
4.17 Using the USB Interface The DE
Page 64 and 65:
Table 4-26 IR Pin Assignments Signa
Page 66 and 67:
• EEPROM The board has 32Kb EEPRO
Page 68 and 69:
SRAM_DQ[7] PIN_AF7 SRAM Data[7] 3.3
Page 70 and 71:
FL_ADDR[15] PIN_Y10 FLASH Address[1
Page 72 and 73:
The top-level design file contains
Page 74 and 75:
• System Configuration Under Syst
Page 76 and 77:
Figure 5-6 HSMC Expansion Group The
Page 78 and 79:
Chapter 6 Examples of Advanced Demo
Page 80 and 81:
Finally, the YcrCb_to_RGB block con
Page 82 and 83:
mouse connected to DE2-115 board. W
Page 84 and 85:
sends a different USB packet to the
Page 86 and 87:
Figure 6-7 Block diagram of the Kar
Page 88 and 89:
Figure 6-9 Block Diagram of the SD
Page 90 and 91:
Figure 6-11 Insert SD Card for the
Page 92 and 93:
Main WAVE Lib System Call SEG7 I2C
Page 94 and 95:
Figure 6-15 The setup for the SD mu
Page 96 and 97:
Figure 6-16 Waveforms on two lines
Page 98 and 99:
Figure 6-18 Remote controller Table
Page 100 and 101:
We can apply the IR receiver to man
Page 102 and 103:
Figure 6-23 Block diagram of the Mu
Page 104 and 105:
Figure 6-24 The Setup of the Music
Page 106 and 107:
• Demonstration Setup, File Locat
Page 108 and 109:
Figure 6-27 MII interface MAC Confi
Page 110 and 111:
Figure 6-29 MAC Options Configurati
Page 112 and 113:
Figure 6-32 PHY connected to the MA
Page 114 and 115:
Ethernet 1 respectively. Table 6-9
Page 116:
Chapter 7 Appendix 7.1 Revision His
show all

DE2-115: User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?