DE2-115: User Manual

More documents

Recommendations

Info

5. The DE2_115_ControlPanel.sof bit stream is loaded automatically as soon as the DE2_115_control_panel.exe is launched. 6. In case the connection is disconnected, click on CONNECT where the .sof will be re-loaded onto the board. 7. Note, the Control Panel will occupy the USB port until you close that port; you cannot use Quartus II to download a configuration file into the FPGA until the USB port is closed. 8. The Control Panel is now ready for use; experience it by setting the ON/OFF status for some LEDs and observing the result on the DE2-115 board. Figure 3-1 The DE2-115 Control Panel The concept of the DE2-115 Control Panel is illustrated in Figure 3-2. The “Control Circuit” that performs the control functions is implemented in the FPGA board. It communicates with the Control Panel window, which is active on the host computer, via the USB Blaster link. The graphical interface is used to issue commands to the control circuit. It handles all requests and performs data transfers between the computer and the DE2-115 board. 15
Figure 3-2 The DE2-115 Control Panel concept The DE2-115 Control Panel can be used to light up LEDs, change the values displayed on 7-segment and LCD displays, monitor buttons/switches status, read/write the SDRAM, SRAM, EEPROM and Flash Memory, monitor the status of an USB device, communicate with the PS/2 mouse, output VGA color pattern to VGA monitor, verify functionality of HSMC connector I/Os, communicate with PC via RS-232 interface and read SD Card specification information. The feature of reading/writing a word or an entire file from/to the Flash Memory allows the user to develop multimedia applications (Flash Audio Player, Flash Picture Viewer) without worrying about how to build a Memory Programmer. 3.2 Controlling the LEDs, 7-segment Displays and LCD Display A simple function of the Control Panel is to allow setting the values displayed on LEDs, 7-segment displays, and the LCD character display. Choosing the LED tab leads to the window in Figure 3-3. Here, you can directly turn the LEDs on or off individually or by clicking “Light All” or “Unlight All”. 16
Page 2 and 3: CONTENTS Chapter 1 DE2-115 Package
Page 4 and 5: 6.9 IR Receiver Demonstration .....
Page 6 and 7: Bag of six rubber (silicon) covers
Page 8 and 9: Chapter 2 Introduction of the Alter
Page 10 and 11: One 40-pin Expansion Header with di
Page 12 and 13: 40-pin expansion port o Configurabl
Page 14 and 15: You can also connect a microphone t
Page 18 and 19: Figure 3-3 Controlling LEDs Choosin
Page 20 and 21: Figure 3-6 Monitoring switches and
Page 22 and 23: The Sequential Read function is use
Page 24 and 25: 3.7 SD Card The function is designe
Page 26 and 27: 1. Choosing the VGA tab leads to th
Page 28 and 29: Figure 3-14 Testing the IR receiver
Page 30 and 31: Chapter 4 Using the DE2-115 Board T
Page 32 and 33: • Configuring the FPGA in JTAG Mo
Page 34 and 35: Figure 4-6 Connections between the
Page 36 and 37: Table 4-1 Pin Assignments for Slide
Page 38 and 39: HEX0[5] PIN_J22 Seven Segment Digit
Page 40 and 41: 4.6 Using the LCD Module The LCD mo
Page 42 and 43: Figure 4-13 HSMC VCCIO supply volta
Page 44 and 45: HSMC_RX_D_N[1] PIN_C27 HSMC_RX_D_N[
Page 46 and 47: HSMC_TX_D_N[14] PIN_U28 HSMC_TX_D_N
Page 48 and 49: The voltage level of the I/O pins o
Page 50 and 51: Figure 4-19 Using Emulated LVDS on
Page 52 and 53: 4.10 Using VGA The DE2-115 board in
Page 54 and 55: Table 4-16 Pin Assignments for ADV7
Page 56 and 57: Figure 4-24 Connections between FPG
Page 58 and 59: You will need to perform a hardware
Page 60 and 61: ENET1_TX_CLK PIN_C22 MII transmit c
Page 62 and 63: 4.17 Using the USB Interface The DE
Page 64 and 65: Table 4-26 IR Pin Assignments Signa
Page 66 and 67:
• EEPROM The board has 32Kb EEPRO
Page 68 and 69:
SRAM_DQ[7] PIN_AF7 SRAM Data[7] 3.3
Page 70 and 71:
FL_ADDR[15] PIN_Y10 FLASH Address[1
Page 72 and 73:
The top-level design file contains
Page 74 and 75:
• System Configuration Under Syst
Page 76 and 77:
Figure 5-6 HSMC Expansion Group The
Page 78 and 79:
Chapter 6 Examples of Advanced Demo
Page 80 and 81:
Finally, the YcrCb_to_RGB block con
Page 82 and 83:
mouse connected to DE2-115 board. W
Page 84 and 85:
sends a different USB packet to the
Page 86 and 87:
Figure 6-7 Block diagram of the Kar
Page 88 and 89:
Figure 6-9 Block Diagram of the SD
Page 90 and 91:
Figure 6-11 Insert SD Card for the
Page 92 and 93:
Main WAVE Lib System Call SEG7 I2C
Page 94 and 95:
Figure 6-15 The setup for the SD mu
Page 96 and 97:
Figure 6-16 Waveforms on two lines
Page 98 and 99:
Figure 6-18 Remote controller Table
Page 100 and 101:
We can apply the IR receiver to man
Page 102 and 103:
Figure 6-23 Block diagram of the Mu
Page 104 and 105:
Figure 6-24 The Setup of the Music
Page 106 and 107:
• Demonstration Setup, File Locat
Page 108 and 109:
Figure 6-27 MII interface MAC Confi
Page 110 and 111:
Figure 6-29 MAC Options Configurati
Page 112 and 113:
Figure 6-32 PHY connected to the MA
Page 114 and 115:
Ethernet 1 respectively. Table 6-9
Page 116:
Chapter 7 Appendix 7.1 Revision His
show all

DE2-115: User Manual

Create successful ePaper yourself

Delete template?

Save as template?